- 您现在的位置：买卖IC网 > PDF目录19350 > MAX6694UE9A+T (Maxim Integrated)IC TEMP MONITOR 5CH 16TSSOP PDF资料下载
参数资料
| 型号： | MAX6694UE9A+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 10/18页 |
| 文件大小： | 196K |
| 描述： | IC TEMP MONITOR 5CH 16TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | 温度监控系统（传感器） |
| 传感器类型： | 内部和外部 |
| 感应温度： | -40°C ~ 125°C，外部传感器 |
| 精确度： | ±3°C 本地（最大），±4°C 远程（最大） |
| 拓扑： | ADC，缓冲器，多路复用器，寄存器库 |
| 输出类型： | SMBus? |
| 输出警报： | 是 |
| 输出风扇： | 是 |
| 电源电压： | 3 V ~ 3.6 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 带卷 (TR) |
5-Channel Precision Temperature Monitor
with Beta Compensation
10 ______________________________________________________________________________________
can be read from the local temperature and remote
temperature registers. The remaining 3 bits for remote
diode 1 can be read from the extended temperature
register. If extended resolution is desired, the extended
resolution register should be read first. This prevents
the most significant bits from being overwritten by new
conversion results until they have been read. If the
most significant bits have not been read within an
SMBus timeout period (nominally 37ms), normal updat-
ing continues. Table 1 shows the main temperature
register (high-byte) data format, and Table 2 shows the
extended resolution register (low-byte) data format.
Diode Fault Detection
If a channels input DXP_ and DXN_ are left open, the
MAX6694 detects a diode fault. An open diode fault
does not cause either ALERT or OVERT to assert. A bit
in the status register for the corresponding channel is
set to 1 and the temperature data for the channel is
stored as all 1s (FFh). It takes approximately 4ms for
the MAX6694 to detect a diode fault. Once a diode fault
is detected, the MAX6694 goes to the next channel in
the conversion sequence.
Alarm Threshold Registers
There are seven alarm threshold registers that store
overtemperature ALERT and OVERT threshold values.
Five of these registers are dedicated to storing one
local alert temperature threshold limit and four remote
alert temperature threshold limits (see the ALERT
Interrupt Mode section). The remaining two registers
are dedicated to remote channels 1 and 4 to store
overtemperature threshold limits (see the OVERT
Overtemperature Alarm section). Access to these regis-
ters is provided through the SMBus interface.
ALERT Interrupt Mode
An ALERT interrupt occurs when the internal or external
temperature reading exceeds a high-temperature limit
(user programmable). The ALERT interrupt output signal
can be cleared by reading the status register(s) associ-
ated with the fault(s) or by successfully responding to an
alert response address transmission by the master. In
both cases, the alert is cleared but is reasserted at the
end of the next conversion if the fault condition still
exists. The interrupt does not halt automatic conversions.
The ALERT output is open-drain so that multiple devices
can share a common interrupt line. All ALERT interrupts
can be masked using the configuration 2 register. The
POR state of these registers is shown in Table 3.
ALERT Response Address
The SMBus alert response interrupt pointer provides
quick fault identification for simple slave devices that
lack the complex logic needed to be a bus master.
Upon receiving an interrupt signal, the host master can
broadcast a receive byte transmission to the alert
response slave address (see the Slave Address sec-
tion). Then, any slave device that generated an inter-
rupt attempts to identify itself by putting its own
address on the bus.
The alert response can activate several different slave
devices simultaneously, similar to the I
2
C General Call.
If more than one slave attempts to respond, bus arbitra-
tion rules apply, and the device with the lower address
code wins. The losing device does not generate an
acknowledgment and continues to hold the ALERT line
low until cleared. (The conditions for clearing an alert
vary depending on the type of slave device.)
Successful completion of the alert response protocol
clears the output latch. If the condition that caused the
alert still exists, the MAX6694 reasserts the ALERT
interrupt at the end of the next conversion.
OVERT Overtemperature Alarms
The MAX6694 has two overtemperature registers that
store remote alarm threshold data for the OVERT output.
OVERT is asserted when a channels measured temper-
ature is greater than the value stored in the correspond-
ing threshold register. OVERT remains asserted until the
temperature drops below the programmed threshold
minus 4癈 hysteresis. An overtemperature output can
be used to activate a cooling fan, send a warning, initi-
ate clock throttling, or trigger a system shutdown to pre-
vent component damage. See Table 3 for the POR state
of the overtemperature threshold registers.
Command Byte Functions
The 8-bit command byte register (Table 3) is the master
index that points to the various other registers within the
MAX6694. This registers POR state is 0000 0000.
相关PDF资料 |
PDF描述 |
|---|---|
| VI-25R-CW-F2 | CONVERTER MOD DC/DC 7.5V 100W |
| TAJY227K004RNJ | CAP TANT 220UF 4V 10% 2917 |
| TAJY227K002RNJ | CAP TANT 220UF 2.5V 10% 2917 |
| TPSD685M035R0400 | CAP TANT 6.8UF 35V 20% 2917 |
| VI-B3J-CY-S | CONVERTER MOD DC/DC 36V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6695AUB | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX6695AUB+ | 功能描述:板上安装温度传感器 Remote/Local Temperature Sensor RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX6695AUB+C5L | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX6695AUB+T | 功能描述:板上安装温度传感器 Remote/Local Temperature Sensor RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX6695AUB-T | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
发布紧急采购，3分钟左右您将得到回复。