- 您现在的位置：买卖IC网 > PDF目录67802 > MAX6695AUB+ (MAXIM INTEGRATED PRODUCTS INC) Dual Remote/Local Temperature Sensors with SMBus Serial Interface PDF资料下载
参数资料
| 型号： | MAX6695AUB+ |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 温度/湿度传感器 |
| 英文描述： | Dual Remote/Local Temperature Sensors with SMBus Serial Interface |
| 中文描述： | DIGITAL TEMP SENSOR-SERIAL, 11BIT(s), 1.50Cel, SQUARE, SURFACE MOUNT |
| 封装： | 3 X 3 MM, LEAD FREE, MO-187C-BA, USOP-10 |
| 文件页数： | 21/22页 |
| 文件大小： | 335K |
| 代理商： | MAX6695AUB+ |
MAX6695/MAX6696
In this example, the effect of the series resistance and
the ideality factor partially cancel each other.
Discrete Remote Diodes
When the remote-sensing diode is a discrete transistor,
its collector and base must be connected together.
Table 1 lists examples of discrete transistors that are
appropriate for use with the MAX6695/MAX6696.
The transistor must be a small-signal type with a rela-
tively high forward voltage; otherwise, the A/D input
voltage range can be violated. The forward voltage at
the highest expected temperature must be greater than
0.25V at 10A, and at the lowest expected tempera-
ture, the forward voltage must be less than 0.95V at
100A. Large power transistors must not be used. Also,
ensure that the base resistance is less than 100
. Tight
specifications for forward current gain (50 < <150, for
example) indicate that the manufacturer has good
process controls and that the devices have consistent
VBE characteristics.
Manufacturers of discrete transistors do not normally
specify or guarantee ideality factor. This is normally not
a problem since good-quality discrete transistors tend
to have ideality factors that fall within a relatively narrow
range. We have observed variations in remote tempera-
ture readings of less than
±2°C with a variety of dis-
crete transistors. Still, it is good design practice to
verify good consistency of temperature readings with
several discrete transistors from any manufacturer
under consideration.
Thermal Mass and Self-Heating
When sensing local temperature, these temperature
sensors are intended to measure the temperature of the
PC board to which they are soldered. The leads pro-
vide a good thermal path between the PC board traces
and the die. As with all IC temperature sensors, thermal
conductivity between the die and the ambient air is
poor by comparison, making air temperature measure-
ments impractical. Because the thermal mass of the PC
board is far greater than that of the MAX6695/
MAX6696, the device follows temperature changes on
the PC board with little or no perceivable delay.
When measuring the temperature of a CPU or other IC
with an on-chip sense junction, thermal mass has virtu-
ally no effect; the measured temperature of the junction
tracks the actual temperature within a conversion cycle.
When measuring temperature with discrete remote
transistors, the best thermal response times are
obtained with transistors in small packages (i.e., SOT23
or SC70). Take care to account for thermal gradients
between the heat source and the sensor, and ensure
that stray air currents across the sensor package do
not interfere with measurement accuracy.
Self-heating does not significantly affect measurement
accuracy. Remote-sensor self-heating due to the diode
current source is negligible. For local temperature mea-
surements, the worst-case error occurs when autocon-
verting at the fastest rate and simultaneously sinking
maximum current at the ALERT output. For example,
with VCC = 3.6V, a 4Hz conversion rate and ALERT
sinking 1mA, the typical power dissipation is:
θJ-A for the 16-pin QSOP package is about +120°C/W,
so assuming no copper PC board heat sinking, the
resulting temperature rise is:
Even under these worst-case circumstances, it is diffi-
cult to introduce significant self-heating errors.
ADC Noise Filtering
The integrating ADC has good noise rejection for low-
frequency signals such as power-supply hum. In envi-
ronments with significant high-frequency EMI, connect
an external 2200pF capacitor between DXP_ and DXN.
Larger capacitor values can be used for added filter-
ing, but do not exceed 3300pF because it can intro-
duce errors due to the rise time of the switched current
source. High-frequency noise reduction is needed for
high-accuracy remote measurements. Noise can be
reduced with careful PC board layout as discussed in
the PC Board Layout section.
Low-Power Standby Mode
Standby mode reduces the supply current to less than
10A by disabling the ADC. Enter hardware standby
(MAX6696 only) by forcing STBY low, or enter software
standby by setting the RUN/STOP bit to 1 in the config-
TmW
C W
C
=×
°
= +
°
2 2
120
0 264
./
.
VA
V
mA
mW
CC ×+
×
=
500
0 4
1
2 2
..
Dual Remote/Local Temperature Sensors with
SMBus Serial Interface
8
_______________________________________________________________________________________
MANUFACTURER
MODEL NO.
Central Semiconductor (USA)
CMPT3904
Rohm Semiconductor (USA)
SST3904
Samsung (Korea)
KST3904-TF
Siemens (Germany)
SMBT3904
Zetex (England)
FMMT3904CT-ND
Table 1. Remote-Sensor Transistor
Manufacturers
Note: Discrete transistors must be diode connected (base
shorted to collector).
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6695AUB+T | Dual Remote/Local Temperature Sensors with SMBus Serial Interface |
| MAX6695YAUB+ | Dual Remote/Local Temperature Sensors with SMBus Serial Interface |
| MAX6695YAUB+T | Dual Remote/Local Temperature Sensors with SMBus Serial Interface |
| MAX6696AEE+ | Dual Remote/Local Temperature Sensors with SMBus Serial Interface |
| MAX6697EP34+ | 7-Channel Precision Temperature Monitor |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6695AUB+ | 功能描述:板上安装温度传感器 Remote/Local Temperature Sensor RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX6695AUB+C5L | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX6695AUB+T | 功能描述:板上安装温度传感器 Remote/Local Temperature Sensor RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX6695AUB-T | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX6695EVCMOD2 | 功能描述:板上安装温度传感器 Evaluation Kit/Evaluation System for the MAX6695 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
发布紧急采购，3分钟左右您将得到回复。