- 您现在的位置：买卖IC网 > PDF目录19488 > MAX6696AEE+T (Maxim Integrated)IC SENSOR TEMP SMBUS 16-QSOP PDF资料下载
参数资料
| 型号： | MAX6696AEE+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 6/19页 |
| 文件大小： | 293K |
| 描述： | IC SENSOR TEMP SMBUS 16-QSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 功能： | 温度监控系统（传感器） |
| 传感器类型： | 内部和外部 |
| 感应温度： | -40°C ~ 125°C，外部传感器 |
| 精确度： | -4.2°C 本地，±3°C 远程（最大） |
| 拓扑： | ADC，多路复用器，寄存器库 |
| 输出类型： | I²C?/SMBus? |
| 输出警报： | 是 |
| 输出风扇： | 是 |
| 电源电压： | 3 V ~ 3.6 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-QSOP |
| 包装： | 标准包装 |
| 产品目录页面： | 1426 (CN2011-ZH PDF) |
| 其它名称： | MAX6696AEE+TDKR |
Detailed Description
The MAX6695/MAX6696 are temperature sensors
designed to work in conjunction with a microprocessor
or other intelligence in temperature monitoring, protec-
tion, or control applications. Communication with the
MAX6695/MAX6696 occurs through the SMBus serial
interface and dedicated alert pins. The overtempera-
ture alarms OT1 and OT2 are asserted if the software-
programmed temperature thresholds are exceeded.
OT1 and OT2 can be connected to a fan, system shut-
down, or other thermal-management circuitry.
The MAX6695/MAX6696 convert temperatures to digital
data continuously at a programmed rate or by selecting
a single conversion. At the highest conversion rate,
temperature conversion results are stored in the main
temperature data registers (at addresses 00h and 01h)
as 7-bit + sign data with the LSB equal to +1癈. At
slower conversion rates, 3 additional bits are available
at addresses 11h and 10h, providing +0.125癈 resolu-
tion. See Tables 2, 3, and 4 for data formats.
ADC and Multiplexer
The MAX6695/MAX6696 averaging ADC (Figure 1) inte-
grates over a 62.5ms or 125ms period (each channel,
typ), depending on the conversion rate (see Electrical
Characteristics table). The use of an averaging ADC
attains excellent noise rejection.
The MAX6695/MAX6696 multiplexer (Figure 1) automat-
ically steers bias currents through the remote and local
diodes. The ADC and associated circuitry measure
each diodes forward voltages and compute the tem-
perature based on these voltages. If a remote channel
is not used, connect DXP_ to DXN. Do not leave DXP_
and DXN unconnected. When a conversion is initiated,
all channels are converted whether they are used or
not. The DXN input is biased at one V
BE
above ground
by an internal diode to set up the ADC inputs for a dif-
ferential measurement. Resistance in series with the
remote diode causes about +1/2癈 error per ohm.
A/D Conversion Sequence
A conversion sequence consists of a local temperature
measurement and two remote temperature measure-
ments. Each time a conversion begins, whether initiat-
ed automatically in the free-running autoconvert mode
(RUN/STOP = 0) or by writing a one-shot command, all
three channels are converted, and the results of the
three measurements are available after the end of con-
version. Because it is common to require temperature
measurements to be made at a faster rate on one of the
remote channels than on the other two channels, the
conversion sequence is Remote 1, Local, Remote 1,
Remote 2. Therefore, the Remote 1 conversion rate is
double that of the conversion rate for either of the other
two channels.
A BUSY status bit in status register 1 (see Table 7 and
the Status Byte Functions section) shows that the
device is actually performing a new conversion. The
results of the previous conversion sequence are always
available when the ADC is busy.
Remote-Diode Selection
The MAX6695/MAX6696 can directly measure the die
temperature of CPUs and other ICs that have on-board
temperature-sensing diodes (see the Typical Operating
Circuit) or they can measure the temperature of a dis-
crete diode-connected transistor.
Effect of Ideality Factor
The accuracy of the remote temperature measurements
depends on the ideality factor (n) of the remote diode
(actually a transistor). The MAX6695/MAX6696 (not the
MAX6695Y/MAX6696Y) are optimized for n = 1.008. A
thermal diode on the substrate of an IC is normally a PNP
with its collector grounded. DXP_ must be connected to
the anode (emitter) and DXN must be connected to the
cathode (base) of this PNP.
If a sense transistor with an ideality factor other than
1.008 is used, the output data will be different from the
data obtained with the optimum ideality factor.
Fortunately, the difference is predictable. Assume a
remote-diode sensor designed for a nominal ideality
factor n
NOMINAL
is used to measure the temperature of
a diode with a different ideality factor n
1
. The measured
temperature T
M
can be corrected using:
where temperature is measured in Kelvin and
n
NOMIMAL
for the MAX6695/MAX6696 is 1.008.
As an example, assume you want to use the MAX6695
or MAX6696 with a CPU that has an ideality factor of
1.002. If the diode has no series resistance, the mea-
sured data is related to the real temperature as follows:
For a real temperature of +85癈 (358.15K), the measured
temperature is +82.87癈 (356.02K), an error of -2.13癈.
Effect of Series Resistance
Series resistance (R
S
) with a sensing diode contributes
additional error. For nominal diode currents of 10糀
T
T
n
n
T
ACTUAL
M
NOMINAL
M
=
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
=
?/DIV>
?/DIV>
?/DIV>
1
1 008
1 002
.
.
湝
?/DIV>
?/DIV>
?/DIV>
=
?/DIV>
(
)
T
M
1 00599
.
T T
n
n
M
ACTUAL
NOMINAL
=
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
1
Dual Remote/Local Temperature Sensors with
SMBus Serial Interface
6 _______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| IRU1207-25CS | IC REG LDO 2.5V 1A 8-SOIC |
| VE-20B-CY-F3 | CONVERTER MOD DC/DC 95V 50W |
| RMC43DRYN | CONN EDGECARD 86POS DIP .100 SLD |
| XC9572XL-5TQ100C | IC CPLD 72 MCELL C-TEMP 100-TQFP |
| VI-B0W-CX-B1 | CONVERTER MOD DC/DC 5.5V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6696YAEE+ | 功能描述:板上安装温度传感器 Remote/Local Temperature Sensor RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX6696YAEE+T | 功能描述:板上安装温度传感器 Remote/Local Temperature Sensor RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX6697AEP | 制造商:Maxim Integrated Products 功能描述:7-CHANNEL PRECISION TEMPERATURE MONITOR - Rail/Tube |
| MAX6697AEP-T | 制造商:Maxim Integrated Products 功能描述:7-CHANNEL PRECISION TEMPERATURE MONITOR - Tape and Reel |
| MAX6697AUP | 制造商:Maxim Integrated Products 功能描述:7-CHANNEL PRECISION TEMPERATURE MONITOR - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。