- 您现在的位置：买卖IC网 > PDF目录19356 > MAX6699UE9C+T (Maxim Integrated)IC TEMP MON 5CH PREC 16TSSOP PDF资料下载
参数资料
| 型号： | MAX6699UE9C+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 16/19页 |
| 文件大小： | 295K |
| 描述： | IC TEMP MON 5CH PREC 16TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | 温度监控系统（传感器） |
| 传感器类型： | 内部和外部 |
| 感应温度： | -40°C ~ 125°C，外部传感器 |
| 精确度： | ±3°C（最小值） |
| 拓扑： | ADC，缓冲器，寄存器库 |
| 输出类型： | I²C?/SMBus? |
| 输出警报： | 是 |
| 输出风扇： | 是 |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 带卷 (TR) |
ADC Noise Filtering
The integrating ADC has good noise rejection for low-
frequency signals, such as power-supply hum. In envi-
ronments with significant high-frequency EMI, connect
an external 2200pF capacitor between DXP_ and
DXN_. Larger capacitor values can be used for added
filtering, but do not exceed 3300pF because it can
introduce errors due to the rise time of the switched
current source. High-frequency noise reduction is
needed for high-accuracy remote measurements.
Noise can be reduced with careful PCB layout as dis-
cussed in the PCB Layout section.
Slave Address
Table 11 shows the MAX6699 slave address.
PCB Layout
Follow these guidelines to reduce the measurement
error when measuring remote temperature:
1) Place the MAX6699 as close as is practical to the
remote diode. In noisy environments, such as a
computer motherboard, this distance can be 4in to
8in (typ). This length can be increased if the worst
noise sources are avoided. Noise sources include
CRTs, clock generators, memory buses, and PCI
buses.
2) Do not route the DXP-DXN lines next to the deflec-
tion coils of a CRT. Also, do not route the traces
across fast digital signals, which can easily intro-
duce +30癈 error, even with good filtering.
3) Route the DXP and DXN traces in parallel and in
close proximity to each other. Each parallel pair of
traces should go to a remote diode. Route these
traces away from any higher voltage traces, such as
+12VDC. Leakage currents from PCB contamination
must be dealt with carefully since a 20M& leakage
path from DXP to ground causes about +1癈 error.
If high-voltage traces are unavoidable, connect
guard traces to GND on either side of the DXP-DXN
traces (Figure 5).
4) Route through as few vias and crossunders as pos-
sible to minimize copper/solder thermocouple
effects.
5) Use wide traces when practical.
6) When the power supply is noisy, add a resistor (up
to 47&) in series with V
CC
.
Twisted-Pair and Shielded Cables
Use a twisted-pair cable to connect the remote sensor
for remote-sensor distances longer than 8in or in very
noisy environments. Twisted-pair cable lengths can be
between 6ft and 12ft before noise introduces excessive
errors. For longer distances, the best solution is a
shielded twisted pair like that used for audio micro-
phones. For example, Belden #8451 works well for dis-
tances up to 100ft in a noisy environment. At the
device, connect the twisted pair to DXP and DXN and
the shield to GND. Leave the shield unconnected at the
5-Channel Precision Temperature Monitor
16 ______________________________________________________________________________________
5 mils
5 mils
5 mils
MINIMUM
5 mils
GND
DXP
DXN
GND
Figure 5. Recommended Minimum DXP-DXN PCB Traces
MANUFACTURER
MODEL NO.
Central Semiconductor (USA)
CMPT3904
Rohm Semiconductor (USA)
SST3904
Samsung (Korea)
KST3904-TF
Siemens (Germany)
SMBT3904
Zetex (England)
FMMT3904CT-ND
Table 10. Remote-Sensors Transistor
Manufacturers
Note: Discrete transistors must be diode connected (base
shorted to collector).
PART
SMBus SLAVE ID
PIN-PACKAGE
MAX
EE 4
0011 010
16 QSOP
MAX
EE
0011 100
16 QSOP
MAX
EE
1001 100
16 QSOP
MAX
EE
1001 110
16 QSOP
MAX
E 4
0011 010
16 TSSOP
MAX
E
0011 100
16 TSSOP
MAX
E
1001 100
16 TSSOP
MAX
E
1001 110
16 TSSOP
Table 11. Slave Address
相关PDF资料 |
PDF描述 |
|---|---|
| VE-B1N-CV-F2 | CONVERTER MOD DC/DC 18.5V 150W |
| SWS1000L-12 | PWR SUP MED 12V 88A SGL OUTPUT |
| VE-B1N-CV-F1 | CONVERTER MOD DC/DC 18.5V 150W |
| SWS1000L-48 | PWR SUP MED 48V 22A SGL OUTPUT |
| VE-B12-CV-F4 | CONVERTER MOD DC/DC 15V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX669EUB | 功能描述:电流型 PWM 控制器 1.8V to 28V Step-Up RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX669EUB/V+ | 功能描述:电流型 PWM 控制器 1.8V to 28V Step-Up RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX669EUB/V+T | 功能描述:电流型 PWM 控制器 1.8V to 28V Step-Up RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX669EUB+ | 功能描述:电流型 PWM 控制器 1.8V to 28V Step-Up RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX669EUB+T | 功能描述:电流型 PWM 控制器 1.8V to 28V Step-Up RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。