- 您现在的位置：买卖IC网 > PDF目录13793 > MAX6720AUTTID3+T (Maxim Integrated Products)IC SUPERVISOR MPU SOT23-6 PDF资料下载
参数资料
| 型号： | MAX6720AUTTID3+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 10/19页 |
| 文件大小： | 0K |
| 描述： | IC SUPERVISOR MPU SOT23-6 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 多压监控器 |
| 监视电压数目： | 3 |
| 输出： | 推挽式，图腾柱 |
| 复位： | 低有效 |
| 复位超时： | 最小为 140 ms |
| 电压 - 阀值： | 1.388V，3.075V，可调 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-6 |
| 供应商设备封装： | SOT-6 |
| 包装： | 带卷 (TR) |
Dual/Triple Ultra-Low-Voltage SOT23 μP
Supervisory Circuits
restarts. The MAX6715/MAX6717/MAX6719/MAX6721/
MAX6723/MAX6725/MAX6727/MAX6728 contain open-
drain reset outputs, while the MAX6716/MAX6718/
MAX6720/MAX6722/MAX6724/MAX6726/MAX6729
contain push-pull reset outputs. The MAX6727 provides
two separate open-drain RST outputs driven by the
same internal logic.
V EXT_TH
R1
RSTIN
MAX6719/
MAX6720/
MAX6723–
MAX6727
Manual Reset Input
Many microprocessor-based products require manual
reset capability, allowing the operator, a test techni-
cian, or external logic circuitry to initiate a reset. A logic
low on MR asserts the reset output. Reset remains
asserted while MR is low and for the reset timeout peri-
od (t RP ) after MR returns high. This input has an internal
50k ? pullup resistor to V CC 1 and can be left uncon-
nected if not used. MR can be driven with TTL or
CMOS logic levels, or with open-drain/collector outputs.
Connect a normally open momentary switch from MR to
GND to create a manual reset function; external
debounce circuitry is not required. If MR is driven from
long cables or if the device is used in a noisy environ-
ment, connect a 0.1μF capacitor from MR to GND to
provide additional noise immunity.
Adjustable Input Voltage
The MAX6719/MAX6720 and MAX6723–MAX6727 provide
an additional input to monitor a third system voltage. The
threshold voltage at RSTIN is typically 626mV. Connect a
resistor-divider network to the circuit as shown in Figure 1
to establish an externally controlled threshold voltage,
V EXT_TH .
V EXT_TH = 626mV((R1 + R2)/R2)
Low leakage current at RSTIN allows the use of large-
valued resistors resulting in reduced power consump-
tion of the system.
Watchdog Input
The watchdog monitors μP activity through the watch-
R2
GND
Figure 1. Monitoring a Third Voltage
when processor activity fails. After each reset event
(V CC power-up/brownout, manual reset, or watchdog
reset), there is a long initial watchdog period of 35s
minimum. The long watchdog period mode provides an
extended time for the system to power-up and fully ini-
tialize all μP and system components before assuming
responsibility for routine watchdog updates.
The normal watchdog timeout period (1.12s min)
begins after the first transition on WDI before the con-
clusion of the long initial watchdog period (Figure 2).
During the normal operating mode, the supervisor will
issue a reset pulse for the reset timeout period if the μP
does not update the WDI with a valid transition (high-to-
low or low-to-high) within the standard timeout period
(1.12s min).
Power-Fail Comparator
PFI is the noninverting input to a comparator. If PFI is
less than V PFI (626.5mV), PFO goes low. Common uses
for the power-fail comparator include monitoring prereg-
ulated input of the power supply (such as a battery) or
V TH
dog input (WDI). To use the watchdog function, con-
nect WDI to a bus line or μP I/O line. When WDI
V CC
t WDI-NORMAL
1.12s MAX
remains high or low for longer than the watchdog time-
out period, the reset output asserts.
The MAX6721–MAX6729 include a dual-mode watch-
dog timer to monitor μP activity. The flexible timeout
architecture provides a long period initial watchdog
mode, allowing complicated systems to complete
WDI
t WDI-STARTUP
35s MAX
1.12s MAX
lengthy boots, and a short period normal watchdog
RESET
t RP
mode, allowing the supervisor to provide quick alerts
Figure 2. Normal Watchdog Startup Sequence
10
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| RCM43DRYN | CONN EDGECARD 86POS DIP .156 SLD |
| RSM18DRYI | CONN EDGECARD 36POS DIP .156 SLD |
| RMM18DRYI | CONN EDGECARD 36POS DIP .156 SLD |
| RCM43DRYH | CONN EDGECARD 86POS DIP .156 SLD |
| RSM22DREI | CONN EDGECARD 44POS .156 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6720AUTTID4+T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6720AUTTID5+T | 功能描述:监控电路 Triple uPower Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6720AUTTID6+T | 功能描述:监控电路 Triple uPower Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6720AUTTWD1+T | 功能描述:监控电路 Triple uPower Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6720AUTTWD2+T | 功能描述:监控电路 Triple uPower Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。