- 您现在的位置：买卖IC网 > PDF目录13690 > MAX6727AKAZID1+T (Maxim Integrated Products)IC SUPERVISOR MPU SOT23-8 PDF资料下载
参数资料
| 型号： | MAX6727AKAZID1+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 10/18页 |
| 文件大小： | 0K |
| 描述： | IC SUPERVISOR MPU SOT23-8 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 多压监控器 |
| 监视电压数目： | 3 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 低有效 |
| 复位超时： | 最小为 1.1 ms |
| 电压 - 阀值： | 1.388V，2.313V，可调 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-8 |
| 供应商设备封装： | SOT-23-8 |
| 包装： | 带卷 (TR) |
Dual/Triple, Ultra-Low-Voltage, SOT23 μP
Supervisory Circuits
Detailed Description
Supply Voltages
The MAX6715A–MAX6729A/MAX6797A μP supervisory
circuits maintain system integrity by alerting the μP to
fault conditions. These ICs are optimized for systems
that monitor two or three supply voltages. The output-
reset state is guaranteed to remain valid while either
Adjustable Input Voltage
The MAX6719A/MAX6720A and MAX6723A–MAX6727A
provide an additional input to monitor a third system volt-
age. The threshold voltage at RSTIN is typically 626mV.
Connect a resistor-divider network to the circuit as shown
in Figure 1 to establish an externally controlled threshold
voltage, V EXT_TH .
V CC 1 or V CC 2 is above 0.8V.
Threshold Levels
V EXT_TH = 626mV((R1 + R2)/R2)
Input-voltage threshold level combinations are indicat-
ed by a two-letter code in the Reset Voltage Threshold
Suffix Guide (Table 1). Contact factory for availability of
other voltage threshold combinations.
Reset Outputs
The MAX6715A –MAX6729A/MAX6797A provide an
active-low reset output ( RST ) and the MAX6725A/
MAX6726A also provide an active-high (RST) output.
RST, RST , RST1 , and RST2 are asserted when the volt-
age at either V CC 1 or V CC 2 falls below the voltage
threshold level, RSTIN drops below threshold, or MR is
pulled low. Once reset is asserted, it stays low for the
reset timeout period (see Table 2). If V CC 1, V CC 2, or
RSTIN goes below the reset threshold before the reset
timeout period is completed, the internal timer restarts.
The MAX6715A/MAX6717A/MAX6719A/MAX6721A/
MAX6723A/MAX6725A/MAX6727A/MAX6728A contain
open-drain reset outputs, while the MAX6716A/
MAX6718A/MAX6720A/MAX6722A/MAX6724A/
MAX6726A/MAX6729A/MAX6797A contain push-pull
reset outputs. The MAX6727A provides two separate
open-drain RST outputs driven by the same internal logic.
Manual-Reset Input
Many μP-based products require manual-reset capabil-
ity, allowing the operator, a test technician, or external
logic circuitry to initiate a reset. A logic-low on MR
asserts the reset output. Reset remains asserted while
Low-leakage current at RSTIN allows the use of large-
valued resistors resulting in reduced power consump-
tion of the system.
Watchdog Input
The watchdog monitors μP activity through the watch-
dog input (WDI). To use the watchdog function, con-
nect WDI to a bus line or μP I/O line. When WDI
remains high or low for longer than the watchdog time-
out period, the reset output asserts.
The MAX6721A–MAX6729A/MAX6797A include a dual-
mode watchdog timer to monitor μP activity. The flexi-
ble timeout architecture provides a long period initial
watchdog mode, allowing complicated systems to
complete lengthy boots, and a short period normal
watchdog mode, allowing the supervisor to provide
quick alerts when processor activity fails. After each
reset event (V CC power-up/brownout, manual reset, or
watchdog reset), there is a long initial watchdog period
of 35s minimum. The long watchdog period mode pro-
vides an extended time for the system to power-up and
fully initialize all μP and system components before
assuming responsibility for routine watchdog updates.
MR is low for the reset timeout period (t RP ) after MR
returns high. This input has an internal 50k ? pullup
resistor to V CC 1 and can be left unconnected if not
used. MR can be driven with CMOS logic levels, or with
open-drain/collector outputs. Connect a normally open
V EXT_TH
R1
RSTIN
MAX6719A/
MAX6720A/
MAX6723A–
MAX6727A
momentary switch from MR to GND to create a manual-
reset function; external debounce circuitry is not
required. If MR is driven from long cables or if the
device is used in a noisy environment, connect a 0.1μF
R2
GND
capacitor from MR to GND to provide additional noise
immunity.
Figure 1. Monitoring a Third Voltage
10
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| 4448-12M | TOROID PWR HI CURRENT 8.0UH SMD |
| MAX6727AKAZID2+T | IC SUPERVISOR MPU SOT23-8 |
| VI-J6Y-CY | CONVERTER MOD DC/DC 3.3V 33W |
| MAX6727AKAWID2+T | IC SUPERVISOR MPU SOT23-8 |
| 4448R-10M | TOROID PWR HI CURRENT 5.0UH SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6727AKAZID2+T | 功能描述:监控电路 Triple uPower Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6727AKAZID3+T | 功能描述:监控电路 Triple uPower Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6727AKAZID4+T | 功能描述:监控电路 Dual/Triple Ultra-Low-Voltage SOT23 N
|
| MAX6727AKAZID5+T | 功能描述:监控电路 Triple uPower Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6727AKAZID6+T | 功能描述:监控电路 Triple uPower Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。