- 您现在的位置：买卖IC网 > PDF目录13690 > MAX6727AKAZID2+T (Maxim Integrated Products)IC SUPERVISOR MPU SOT23-8 PDF资料下载
参数资料
| 型号： | MAX6727AKAZID2+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 13/18页 |
| 文件大小： | 0K |
| 描述： | IC SUPERVISOR MPU SOT23-8 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 多压监控器 |
| 监视电压数目： | 3 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 低有效 |
| 复位超时： | 最小为 8.8 ms |
| 电压 - 阀值： | 1.388V，2.313V，可调 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-8 |
| 供应商设备封装： | SOT-23-8 |
| 包装： | 带卷 (TR) |
Dual/Triple, Ultra-Low-Voltage, SOT23 μP
Supervisory Circuits
magnitude indicated (reset threshold overdrive). The
graph shows the maximum pulse width that a negative-
going V CC transient may typically have without causing
a reset pulse to be issued. As the amplitude of the tran-
sient increases (i.e., goes farther below the reset
threshold), the maximum allowable pulse width
decreases. A 0.1μF bypass capacitor mounted close to
the V CC pin provides additional transient immunity.
Watchdog Software Considerations
Setting and resetting the watchdog input at different
points in the program, rather than “pulsing” the watch-
dog input high-low-high or low-high-low, helps the
watchdog timer to closely monitor software execution.
This technique avoids a “stuck” loop where the watch-
dog timer continues to be reset within the loop, keeping
START
SET WDI
HIGH
PROGRAM
CODE
SUBROUTINE OR
PROGRAM LOOP
SET WDI LOW
the watchdog from timing out. Figure 6 shows an exam-
ple flow diagram where the I/O driving the watchdog
input is set high at the beginning of the program, set low
at the beginning of every subroutine or loop, then set
high again when the program returns to the beginning. If
the program should “hang” in any subroutine, the I/O is
SUBROUTINE
COMPLETED
RETURN
HANG IN
SUBROUTINE
continually set low and the watchdog timer is allowed to
time out, causing a reset or interrupt to be issued.
Figure 6. Watchdog Flow Diagram
______________________________________________________________________________________
13
相关PDF资料 |
PDF描述 |
|---|---|
| VI-J6Y-CY | CONVERTER MOD DC/DC 3.3V 33W |
| MAX6727AKAWID2+T | IC SUPERVISOR MPU SOT23-8 |
| 4448R-10M | TOROID PWR HI CURRENT 5.0UH SMD |
| MAX6727AKAZGD5+T | IC SUPERVISOR MPU SOT23-8 |
| VI-J6Y-CX | CONVERTER MOD DC/DC 3.3V 49.5W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6727AKAZID3+T | 功能描述:监控电路 Triple uPower Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6727AKAZID4+T | 功能描述:监控电路 Dual/Triple Ultra-Low-Voltage SOT23 N
|
| MAX6727AKAZID5+T | 功能描述:监控电路 Triple uPower Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6727AKAZID6+T | 功能描述:监控电路 Triple uPower Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6727AKAZWD1+T | 功能描述:监控电路 Triple uPower Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。