- 您现在的位置：买卖IC网 > PDF目录132690 > MAX6735KATED5-T (MAXIM INTEGRATED PRODUCTS INC) Pch Power MOSFET; Surface Mount Type: N/Y; Package: PW-MOLD; Number Of Pins: 3; R DS On (Ω): (max 0.25) (max 0.17); I_S (A): (max -5) PDF资料下载
参数资料
| 型号： | MAX6735KATED5-T |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 电源管理 |
| 英文描述： | Pch Power MOSFET; Surface Mount Type: N/Y; Package: PW-MOLD; Number Of Pins: 3; R DS On (Ω): (max 0.25) (max 0.17); I_S (A): (max -5) |
| 中文描述： | 3-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| 封装： | SOT-23, 8 PIN |
| 文件页数： | 2/15页 |
| 文件大小： | 199K |
| 代理商： | MAX6735KATED5-T |
MAX6730–MAX6735
The RSTIN comparator derives power from VCC1, and
the input voltage must remain less than or equal to
VCC1. Low leakage current at RSTIN allows the use of
large-valued resistors, resulting in reduced power con-
sumption of the system.
Watchdog
The watchdog feature monitors P activity through
the watchdog input (WDI). A rising or falling edge on
WDI within the watchdog timeout period (tWD) indi-
cates normal P operation. WDO asserts low if WDI
remains high or low for longer than the watchdog
timeout period. Floating WDI does not disable the
watchdog timer.
The MAX6730–MAX6735 include a dual-mode watch-
dog timer to monitor P activity. The flexible timeout
architecture provides a long-period initial watchdog
mode, allowing complicated systems to complete
lengthy boots, and a short-period normal watchdog
mode, allowing the supervisor to provide quick alerts
when processor activity fails. After each reset event
(VCC power-up, brownout, or manual reset), there is a
long initial watchdog period of 35s (min). The long
watchdog period mode provides an extended time for
the system to power up and fully initialize all P and
system components before assuming responsibility for
routine watchdog updates.
The usual watchdog timeout period (1.12s min) begins
after the initial watchdog timeout period (tWD-L) expires
or after the first transition on WDI (Figure 3). During nor-
mal operating mode, the supervisor asserts the WDO
output if the P does not update the WDI with a valid
transition (high to low or low to high) within the standard
timeout period (tWD-S) (1.12s min).
Connect MR to WDO to force a system reset in the
event that no rising or falling edge is detected at WDI
within the watchdog timeout period. WDO asserts low
when no edge is detected by WDI, the RST output
asserts low, the watchdog counter immediately clears,
and WDO returns high. The watchdog counter restarts,
using the long watchdog period, when the reset timeout
period ends (Figure 4).
Ensuring a Valid RESET
Output Down to VCC = 0
The MAX6730–MAX6735 guarantee proper operation
down to VCC = +0.8V. In applications that require valid
reset levels down to VCC = 0, use a 100k
Ω pulldown
resistor from RST to GND. The resistor value used is not
critical, but it must be large enough not to load the
reset output when VCC is above the reset threshold. For
most applications, 100k
Ω is adequate. Note that this
configuration does not work for the open-drain outputs
of MAX6730/MAX6732/MAX6734.
Single-/Dual-/Triple-Voltage P Supervisory
Circuits with Independent Watchdog Output
10
______________________________________________________________________________________
tRP
VTH
VCC
(MIN)
VCC1,
VCC2
RSTIN
RST
WDO
WDI
< tWD-S
> tWD-S
tWD-S
< tWD-S
< tWD-L
Figure 3. Watchdog Input/Output Timing Diagram (MR and WDO Not Connected)
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6735KATED6-T | Pch Power MOSFET; Surface Mount Type: N/Y; Package: TPS; Number Of Pins: 3; R DS On (Ω): (max 0.25) (max 0.17); I_S (A): (max -5) |
| MAX6735KATGD1-T | Pch Power MOSFET; Surface Mount Type: N/Y; Package: NEW PW-MOLD2; Number Of Pins: 3; R DS On (Ω): (max 2.0); I_S (A): (max -2.5) |
| MAX6735KATGD2-T | Pch Power MOSFET; Surface Mount Type: N/Y; Package: NEW PW-MOLD2; Number Of Pins: 3; R DS On (Ω): (max 0.25) (max 0.17); I_S (A): (max -5) |
| MAX6735KATGD3-T | Pch Power MOSFET; Surface Mount Type: N; Package: VS-6; R DS On (Ω): (max 0.12) (max 0.06) (max 0.04); I_S (A): (max -4.5) |
| MAX6735KATGD4-T | Pch Power MOSFET; ; Package: VS-6; Number Of Pins: 6; Application Scope: mobile; R DS On (Ω): (max 0.3) (max 0.16) (max 0.11); I_S (A): (max -4.5) |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6735KATED6+T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6735KATED6-T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6735KATGD1+T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6735KATGD1-T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6735KATGD2+T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。