- 您现在的位置：买卖IC网 > PDF目录1845 > MAX6751KA16+T (Maxim Integrated Products)IC MPU W/ADJ RESET CIRC SOT23-8 PDF资料下载
参数资料
| 型号： | MAX6751KA16+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 6/14页 |
| 文件大小： | 0K |
| 描述： | IC MPU W/ADJ RESET CIRC SOT23-8 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 多压监控器 |
| 监视电压数目： | 2 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 低有效 |
| 复位超时： | 可调节/可选择 |
| 电压 - 阀值： | 1.575V，可调 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-8 |
| 供应商设备封装： | SOT-23-8 |
| 包装： | 带卷 (TR) |
MAX6746–MAX6753
μP Reset Circuits with Capacitor-Adjustable
Reset/Watchdog Timeout Delay
Pin Description (continued)
PIN
MAX6746
MAX6747
MAX6748–
MAX6751
MAX6752
MAX6753
NAME
FUNCTION
Watchdog Select Input. WDS selects the watchdog mode. Connect
WDS to ground to select normal mode and the watchdog timeout
5
5
—
WDS
period. Connect WDS to V CC to select extended mode, multiplying the
basic timeout period by a factor of 128. A change in the state of WDS
clears the watchdog timer.
—
—
5
SET1
Logic Input. SET1 selects the watchdog window ratio or disables the
watchdog timer. See Table 1.
Watchdog Input.
MAX6746–MAX6751: A falling transition must occur on WDI within the
selected watchdog timeout period or a reset pulse occurs. The
watchdog timer clears when a transition occurs on WDI or whenever
RESET is asserted. Connect SWT to ground to disable the watchdog
timer function.
6
6
6
WDI
MAX6752/MAX6753: WDI falling transitions within periods shorter than
t WD1 or longer than t WD2 force RESET to assert low for the reset timeout
period. The watchdog timer begins to count after RESET is deasserted.
The watchdog timer clears when a valid transition occurs on WDI or
whenever RESET is asserted. Connect SET0 high and SET1 low to
disable the watchdog timer function. See the Watchdog Timer section.
Push/Pull or Open-Drain Reset Output. RESET asserts whenever V CC or
RESET IN drops below the selected reset threshold voltage (V TH or
7
7
7
RESET
V RESET IN , respectively) or manual reset is pulled low. RESET remains
low for the reset timeout period after all reset conditions are deasserted,
and then goes high. The watchdog timer triggers a reset pulse (t RP )
whenever a watchdog fault occurs.
8
8
8
V CC
Supply Voltage. V CC is the power-supply input and the input for fixed
threshold V CC monitor.
6
Maxim Integrated
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6752KA31+T | MCU RESET CIRCUIT SOT23-8 |
| MAX675ESA+T | IC VREF SERIES PREC 5V 8-SOIC |
| MAX6760TARAD3+T | IC DETECT VOLT WINDOW 8-TDFN |
| MAX6773TALD2+T | IC REG LINEAR 5V 8TDFN |
| MAX6783TEC+ | IC BATT MON QUAD 10% 16TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6751KA17 | 制造商:Maxim Integrated Products 功能描述:SINGLE/DUAL-VOLT MICROPROC. RESET C - Cut Tape Product |
| MAX6751KA17/V+T | 功能描述:监控电路 Dual uPower Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6751KA17+ | 制造商:Maxim from Components Direct 功能描述:MAXIM MAX6751KA17+ PROCESSOR SUPERVISORS - Tape and Reel 制造商:Maxim 功能描述:Maxim MAX6751KA17+ Processor Supervisors |
| MAX6751KA17+T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6751KA17-T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。