- 您现在的位置：买卖IC网 > PDF目录299461 > MAX6755UK_D_-T (Maxim Integrated Products, Inc.) CLAMP PDF资料下载
参数资料
| 型号： | MAX6755UK_D_-T |
| 厂商： | Maxim Integrated Products, Inc. |
| 英文描述： | CLAMP |
| 中文描述： | 低功耗，单/双电压窗检测器 |
| 文件页数： | 6/23页 |
| 文件大小： | 307K |
| 代理商： | MAX6755UK_D_-T |
MAX6754–MAX6764
Low-Power, Single/Dual-Voltage Window
Detectors
14
______________________________________________________________________________________
Choose R2 to have a resistance of up to 500k
.
Calculate R1 by:
R1 = ((V+ - 0.4255V) x R2) / 0.4255V
The MAX6763/MAX6764 provide inputs to a window
detector allowing the programming of the threshold
voltage to within VCC (see Figure 6).
Choose R1, R2, and R3 such that:
(V+ / (R1 + R2 + R3))
≥ 1A
SET
The MAX6754–MAX6762 allow the setting of the window
voltage range of the voltage detector. Connect SET to
GND to set a
±5% window. Connect SET to VCC for a
±10% window. Bias SET to VCC/2 for a ±15% window.
Manual Reset (
MR)
The MAX6754–MAX6762 include an active-low manual
reset input. Drive MR low to assert a reset output
(MAX6754/MAX6755/MAX6756) or an undervoltage
output (MAX6757/MAX6758/MAX6759). The output
remains asserted for the specified propagation delay
time (see Figure 7) after MR goes high. MR is internally
pulled to VCC with a 26k
resistor.
Overvoltage Latch Control Input
(OVLATCH)
The MAX6760/MAX6761/MAX6762 provide an overvolt-
age latch control input (OVLATCH). Drive OVLATCH
high to latch the overvoltage output for any VCC or
VCC2 overvoltage condition. Drive OVLATCH low to
clear the latch after overvoltage conditions have been
removed. The latch is transparent when OVLATCH is
connected to GND. OVLATCH is a high impedance
input. Use external pullup or pulldown.
Reset, Undervoltage, and Overvoltage
Outputs (RESET,
RESET, UV, UV, OV)
RESET, RESET, UV, UV, and OV outputs assert when
the monitored supply is below the selected UVTH
threshold or above the selected OVTH threshold. The
reset output deasserts after the specified timeout peri-
od when the monitored supply rises above the UVTH
threshold or drops below the OVTH threshold. The
push-pull versions are referenced to VCC.
The MAX6760/MAX6761/MAX6762 monitor both VCC
and VCC2. An under/overvoltage condition on either
voltage supply asserts the corresponding output.
RESET and UV are guaranteed to be in the correct
logic state when VCC or VCC2 > 1V.
INTERNAL
REFERENCE
0.5V
GND
OV MONITOR
UV MONITOR
OVTH
UVTH
UV
OV
UVIN
VCC
OVIN
MAX6763/MAX6764
V+
R1
R2
R3
OVERVOLTAGE ASSERTS WHEN
UNDERVOLTAGE ASSERTS WHEN
V+ x R3
R1 + R2 + R3
> 0.5V
< 0.5V
V+ x (R2 + R3)
R1 + R2 + R3
Figure 6. Setting the Under/Overvoltage Window
MR
RESET, UV
tD-MR
tMR_P
Figure 7a. Manual Reset/Reset Timing Diagram
tD-UV
tRP
VCC
RESET, UV
(RESET IS THE COMPLEMENT OF RESET)
Figure 7b. VCC/RESET, UV Timing Diagram
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6756UK_D_-T | Low-Power, Single/Dual-Voltage Window Detectors |
| MAX6757UT_D_-T | Low-Power, Single/Dual-Voltage Window Detectors |
| MAX702CPA | Power-Supply Monitor with Reset |
| MAX8510EXK31-T | 3.1 V FIXED POSITIVE LDO REGULATOR, 0.17 V DROPOUT, PDSO5 |
| MAX8510EXK32-T | 3.2 V FIXED POSITIVE LDO REGULATOR, 0.17 V DROPOUT, PDSO5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6755UKLD0 | 制造商:Maxim Integrated Products 功能描述:LOW-POWER SINGLE/DUAL-VOLTAGE WIND - Cut Tape Product |
| MAX6755UKLD0+ | 制造商:Maxim Integrated Products 功能描述:VOLT SUPERVISOR DETECT 5V 5PIN SOT-23 - Cut Tape Product |
| MAX6755UKLD0+T | 功能描述:监控电路 Single Low Power Window Detector RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6755UKLD0-T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6755UKLD3 | 制造商:Maxim Integrated Products 功能描述:LOW-POWER SINGLE/DUAL-VOLTAGE WIND - Cut Tape Product |
发布紧急采购，3分钟左右您将得到回复。