- 您现在的位置：买卖IC网 > PDF目录67880 > MAX6765TTLD3+ (MAXIM INTEGRATED PRODUCTS INC) Automotive Micropower Linear Regulators with Supervisor PDF资料下载
参数资料
| 型号： | MAX6765TTLD3+ |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 电源管理 |
| 英文描述： | Automotive Micropower Linear Regulators with Supervisor |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, DSO6 |
| 封装： | 3 X 3 MM, 0.80 MM HIEGHT, LEAD FREE, MO-229WEEA, TDFN-6 |
| 文件页数： | 8/46页 |
| 文件大小： | 628K |
| 代理商： | MAX6765TTLD3+ |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页
MAX6765–MAX6774
Automotive Micropower Linear Regulators
with Supervisor
16
______________________________________________________________________________________
Watchdog Timer (MAX6773/MAX6773B/
MAX6774/MAX6774B)
The MAX6773/MAX6774 include a watchdog timer that
asserts RESET if the watchdog input (WDI) does not
toggle within the watchdog timeout period tWD (1.6s
(typ) for the MAX6773/MAX6774 and 50ms (typ) for the
MAX6773B/MAX6774B). RESET remains low for the
reset timeout period, tRP. If the watchdog is not updat-
ed for lengthy periods of time, the reset output appears
as a pulse train, asserted for the reset timeout period
and deasserted for the watchdog timeout period, until
WDI is toggled again. When RESET asserts, it stays low
for the entire reset timeout period ignoring any WDI
transitions. To prevent the watchdog from asserting
RESET, toggle WDI with a valid rising or falling edge
prior to tWD (min). The watchdog counter clears when
WDI toggles prior to tWD or when RESET asserts. The
watchdog resumes counting after RESET deasserts.
The watchdog timer cannot be disabled.
Thermal Protection
When the junction temperature exceeds TJ = +160°C
(typ), an internal thermal sensor signals the shutdown
logic that turns off the pass transistor and allows the IC
to cool. The thermal sensor turns the pass transistor on
again after the IC’s junction temperature cools by 20°C
(typ), resulting in a cycled output during continuous
thermal-overload conditions. Thermal protection pro-
tects the MAX6765–MAX6774B in the event of a fault
condition. Never exceed the absolute maximum junction
temperature rating of TJ = +150°C. See Figures 3 and 4
for the safe operating area.
Applications Information
Output Voltage Selection
The MAX6767–MAX6774B feature dual-mode operation:
these devices operate in either a preset or adjustable
voltage mode. In preset voltage mode, internal trimmed
feedback resistors set the internal linear regulator to
+1.8V, +2.5V, +3.3V, or +5V (see Table 2). Select pre-
set-voltage mode by connecting SET to ground. In
adjustable mode, select an output voltage between
+1.8V and +11V using two external resistors connected
as a voltage-divider to SET (see Figure 1). Set the output
voltage using the following equation:
VOUT = VSET (1 + R1 / R2)
where VSET = 1.233V and the recommended value for
R2 is 50k (maximum 100k).
RESETIN Threshold Selection
The MAX6769/MAX6770 feature an adjustable reset
threshold to monitor the voltage on RESETIN using a
resistive divider between the monitored voltage,
RESETIN and GND. See Figure 2. Use the following for-
mula to set the desired reset threshold:
VMON = VTH (1 + R3 / R4)
where VTH is 1.085V for the M/S/Y/V versions and
1.147V for L/T/Z/W versions.
MAX6769
MAX6770
RESET
RESETIN
R3
R4
GND
IN
VIN
VMON
Figure 2. RESETIN Threshold Selection
OPERATING
STATE
ENABLE
HOLD
REGULATOR
OUTPUT
COMMENT
Initial State
Low
Don’t care
Off
ENABLE is pulled to GND through an internal pulldown. HOLD is
floating (pulled up to OUT). Regulator output is disabled.
Turn-On State
High
Don’t care
On
ENABLE is externally driven high turning the regulator output on.
HOLD is pulled up by OUT.
Hold
Setup State
High
Low
On
HOLD is externally pulled low while ENABLE remains high (latches
HOLD state).
Hold State
Low
On
ENABLE is driven low (or allowed to float low by an internal pulldown).
HOLD remains externally pulled low keeping the regulator output on.
Off-State
Low
High
(floats high)
Off
HOLD is driven high (or allowed to float high by an internal pullup)
while ENABLE is low. Regulator output is shut off and ENABLE/
HOLD logic returns to the initial state.
Table 3. ENABLE/HOLD Truth Table/State Table
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6765TTLD3+T | Automotive Micropower Linear Regulators with Supervisor |
| MAX6765TTLD4+ | Automotive Micropower Linear Regulators with Supervisor |
| MAX6765TTLD4+T | Automotive Micropower Linear Regulators with Supervisor |
| MAX6765TTMD0+ | Automotive Micropower Linear Regulators with Supervisor |
| MAX6765TTMD0+T | Automotive Micropower Linear Regulators with Supervisor |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6765TTLD3+ | 制造商:Maxim Integrated Products 功能描述:REG STD LIN ADJ/FIX POS 1.8V TO 11V/5V 0.1A 6TDFN EP - Rail/Tube |
| MAX6765TTLD3+T | 功能描述:线性稳压器 - 标准 uPower Linear Regulator RoHS:否 制造商:STMicroelectronics 输出类型: 极性: 输出电压:1.8 V 输出电流:150 mA 负载调节: 最大输入电压:5.5 V 线路调整率: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOT-323-5L |
| MAX6765TTLD4+ | 制造商:Maxim Integrated Products 功能描述:REG STD LIN ADJ/FIX POS 1.8V TO 11V/5V 0.1A 6TDFN EP - Rail/Tube |
| MAX6765TTLD4+T | 功能描述:线性稳压器 - 标准 uPower Linear Regulator RoHS:否 制造商:STMicroelectronics 输出类型: 极性: 输出电压:1.8 V 输出电流:150 mA 负载调节: 最大输入电压:5.5 V 线路调整率: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOT-323-5L |
| MAX6765TTMD0+ | 制造商:Maxim Integrated Products 功能描述:REG STD LIN ADJ/FIX POS 1.8V TO 11V/5V 0.1A 6TDFN EP - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。