- 您现在的位置：买卖IC网 > PDF目录13575 > MAX6830SFUT+T (Maxim Integrated Products)IC MPU SUPERVISOR SOT23-6 PDF资料下载
参数资料
| 型号： | MAX6830SFUT+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 10/12页 |
| 文件大小： | 0K |
| 描述： | IC MPU SUPERVISOR SOT23-6 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 多压监控器 |
| 监视电压数目： | 2 |
| 输出： | 推挽式，图腾柱 |
| 复位： | 高有效 |
| 复位超时： | 最小为 140 ms |
| 电压 - 阀值： | 1.05V，2.93V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-6 |
| 供应商设备封装： | SOT-6 |
| 包装： | 带卷 (TR) |
Dual Ultra-Low-Voltage SOT23 μP Supervisors
with Manual Reset and Watchdog Timer
directly to the microcontroller’s RESET pin with a single
pullup resistor allows the device to assert a reset
(Figure 6).
Negative-Going V CC Transients
These supervisors are relatively immune to short-dura-
tion, negative-going V CC transients (glitches), which
usually do not require the entire system to shut down.
Resets are issued to the μP during power-up, power-
down, and brownout conditions. The Typical Operating
Characteristics show a graph of the Maximum V CC
Transient Duration vs. Reset Threshold Overdrive, for
which reset pulses are not generated. The graph was
produced using negative-going V CC pulses, starting at
the standard monitored voltage and ending below the
reset threshold by the magnitude indicated (reset
threshold overdrive). The graph shows the maximum
pulse width that a negative-going V CC transient can
typically have without triggering a reset pulse. As the
amplitude of the transient increases (i.e., goes farther
below the reset threshold), the maximum allowable
pulse width decreases. Typically, a V CC transient that
goes 100mV below the reset threshold and lasts for
20μs or less will not trigger a reset pulse.
Ensuring a Valid RESET
Output Down to V CC = 0
The MAX6826–MAX6831 are guaranteed to operate
properly down to V CC = 1V. In applications that require
valid reset levels down to V CC = 0, a pulldown resistor
to active-low outputs (push/pull only, Figure 7) and a
pullup resistor to active-high outputs (push/pull only) will
ensure that the reset line is valid while the reset output
can no longer sink or source current. This scheme does
not work with the open-drain outputs of the
MAX6828/MAX6831. The resistor value used is not criti-
cal, but it must be small enough not to load the reset
output when V CC is above the reset threshold. For falling
slew rates greater than 1V/s, a 100k ? is adequate.
Watchdog Software Considerations
One way to help the watchdog timer monitor software
execution more closely is to set and reset the watchdog
input at different points in the program, rather than
pulsing the watchdog input high-low-high or low-high-
low. This technique avoids a stuck loop, in which the
watchdog timer would continue to be reset inside the
loop, keeping the watchdog from timing out.
Figure 8 shows an example of a flow diagram where the
I/O driving the watchdog input is set high at the begin-
ning of the program, set low at the beginning of every
subroutine or loop, then set high again when the pro-
gram returns to the beginning. If the program should
hang in any subroutine, the problem would quickly be
corrected, since the I/O is continually set low and the
watchdog timer is allowed to time out, causing a reset
or interrupt to be issued. As described in the Watchdog
Input Current section, this scheme results in higher time
average WDI input current than does leaving WDI low
for the majority of the timeout period and periodically
pulsing it low-high-low.
START
SET WDI
HIGH
PROGRAM
CODE
SUBROUTINE OR
PROGRAM LOOP
SET WDI LOW
V CC
RETURN
MAX6826
MAX6829
RESET
R1
Figure 8. Watchdog Flow Diagram
GND
Figure 7. RESET Valid to V CC = Ground Circuit
100k ?
10
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6830SDUT+T | IC MPU SUPERVISOR SOT23-6 |
| 100ZLH100MEFCG412.5X16 | CAP ALUM 100UF 100V 20% RADIAL |
| MAX6830SVUT+T | IC MPU SUPERVISOR SOT23-6 |
| MAX1832EUT#TG16 | IC REG BST SYNC ADJ .15A SOT23-6 |
| 100ZLH100MEFC12.5X16 | CAP ALUM 100UF 100V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6830SGUT | 制造商:Maxim Integrated Products 功能描述:DUAL ULTRA LOW VOLTAGE SOT23 MICROP - Cut Tape Product |
| MAX6830SGUT+T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6830SGUT-T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6830SHUT | 制造商:Maxim Integrated Products 功能描述:DUAL ULTRA LOW VOLTAGE SOT23 MICROP - Rail/Tube 制造商:Rochester Electronics LLC 功能描述: |
| MAX6830SHUT+ | 制造商:Maxim Integrated Products 功能描述:PROCESSOR SUPERVISOR 2.93V/1.313V 10UA 6PIN SOT-23 - Rail/Tube 制造商:Rochester Electronics LLC 功能描述: |
发布紧急采购，3分钟左右您将得到回复。