参数资料
型号: MAX6835HXSD3+T
厂商: Maxim Integrated Products
文件页数: 6/11页
文件大小: 0K
描述: IC MPU SUPERVISOR SC70-4
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 1
类型: 简单复位/加电复位
监视电压数目: 1
输出: 推挽式,图腾柱
复位: 低有效
复位超时: 最小为 140 ms
电压 - 阀值: 1.313V
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: SC-82A,SOT-343
供应商设备封装: SC-70-4
包装: 标准包装
其它名称: MAX6835HXSD3+TDKR
MAX6832–MAX6840
Ultra-Low-Voltage SC70 Voltage Detectors
and μP Reset Circuits
Functional Diagrams
MR (MAX6835/MAX6836/MAX6837 ONLY)
V CC
MR
V CC
PULLUP
MANUAL
RESET
DETECT
RESET
TIMEOUT
PERIOD
RESET
OUTPUT
RESET-IN
RESET/
RESET
RESET
TIMEOUT
PERIOD
MAX6838/
RESET
OUTPUT
RESET/
RESET
MAX6839/
MAX6832–
V REF = 444mV
MAX6840
V REF = 444mV
MAX6837
GND
GND
Detailed Description
Reset Output
A microprocessor’s (μP’s) reset input starts the μP in a
known state. The MAX6832–MAX6840 assert a reset to
prevent code-execution errors during power-up, power-
down, or brownout conditions. They also assert a reset
signal whenever the V CC supply voltage falls below a
preset threshold (MAX6832–MAX6837) or RESET-IN
falls below the adjustable threshold (MAX6838/
MAX6839/MAX6840), keeping reset asserted for a fixed
timeout delay (Table 2) after V CC or RESET-IN has risen
above the reset threshold. The MAX6832/MAX6835/
MAX6838 use a push-pull active-low output, the
MAX6833/MAX6836/MAX6839 have a push-pull active-
MR is driven from long cables or if the device is used in
a noisy environment, connecting a 0.1μF capacitor from
MR to ground provides additional noise immunity.
RESET-IN Information
The MAX6838/MAX6839/MAX6840 feature a RESET-IN
input for monitoring supply voltages down to 0.44V. An
external resistive-divider network can be used to set
voltage monitoring thresholds as shown in Figure 1. As
the monitored voltage falls, the voltage at RESET-IN
decreases and asserts a reset when it falls below the
RESET-IN threshold (V RSTIN ). The low-leakage current
high output, and the MAX6834/MAX6837/MAX6840
have an open-drain active-low output stage. Connect a
pullup resistor on the MAX6834/MAX6837/MAX6840’s
RESET output to any supply between 0 and 6V.
Manual Reset Input
Many μP-based systems require manual reset capabili-
V MONITORED
R1
RESET-IN
MAX6838/
MAX6839/
MAX6840
RESET
(RESET)
V CC
ty, allowing the operator, a test technician, or external
logic circuitry to initiate a reset. Reset remains asserted
while MR is low, and for a fixed timeout delay after MR
returns high. This input has an internal 20k ? pullup
resistor, so it can be left open if it is not used. MR can
be driven with CMOS logic level, or with open-drain/col-
lector outputs. To create a manual reset function, con-
nect a normally open momentary switch from MR to
R2
GND
R1 = R2 [(V MONITORED /V REF ) -1]
WHERE V MONITORED IS THE DESIRED TRIP LEVEL,
V REF = 444mV
( ) ARE FOR MAX6839
ground; external debounce circuitry is not required. If
6
Figure 1. Setting the Adjustable Threshold Externally
Maxim Integrated
相关PDF资料
PDF描述
LQH43MN680J03L INDUCTOR
LQH43MN561J03L INDUCTOR
TC7662BCOA713 IC REG SWITCHD CAP INV ADJ 8SOIC
CGS962U050R2C CAP ALUM 9600UF 50V SCREW
LQH43MN560J03L INDUCTOR
相关代理商/技术参数
参数描述
MAX6835HXSD4 制造商:Maxim Integrated Products 功能描述:- Rail/Tube
MAX6835HXSD4+ 制造商:Maxim Integrated Products 功能描述:PROCESSOR SUPERVISOR 1.313V 16UA 4PIN SC-70 - Rail/Tube
MAX6835HXSD4+T 功能描述:监控电路 Single uPower Reset Circuit RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟(典型值):10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel
MAX6835HXSD4-T 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟(典型值):10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel
MAX6835IXSD0 制造商:Maxim Integrated Products 功能描述:- Cut Tape Product