- 您现在的位置：买卖IC网 > PDF目录67128 > MAX6841HUKD0+ (MAXIM INTEGRATED PRODUCTS INC) Ultra-Low-Voltage µP Reset Circuits and Voltage Detectors PDF资料下载
参数资料
| 型号： | MAX6841HUKD0+ |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 电源管理 |
| 英文描述： | Ultra-Low-Voltage µP Reset Circuits and Voltage Detectors |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| 封装： | SOT-23, 5 PIN |
| 文件页数： | 6/9页 |
| 文件大小： | 579K |
| 代理商： | MAX6841HUKD0+ |
MAX6841–MAX6845
RESET IN decreases. The MAX6843/MAX6844/
MAX6845 assert a reset when the voltage at RESET IN
falls below the RESET IN threshold (VRSTIN). The low-
leakage current at RESET IN allows for relatively large-
value resistors to be used, which reduces power
consumption. For example, for VCC-TH = 0.9V, if R2 =
100k
, then R1 = 26.3k.
Applications Information
VCC Falling Transients
The MAX6841–MAX6845 are relatively immune to short-
duration falling VCC transients (glitches). Figure 2
shows typical transient duration vs. reset comparator
overdrive, for which the MAX6841–MAX6845 do not
generate a reset pulse. The graph was generated using
a falling pulse applied to VCC, starting 0.1V above the
actual reset threshold and ending below it by the mag-
nitude indicated (reset comparator overdrive). The
graph indicates the maximum pulse width that a falling
VCC transient can have without causing a reset pulse.
As the magnitude of the transient increases (goes fur-
ther below the reset threshold), the maximum allowable
pulse width decreases. A 0.1F bypass capacitor
mounted as close as possible to the VCC pin provides
additional transient immunity.
Ensuring a Valid Reset Output
Down to VCC = 0
When VCC falls below 0.55V, the MAX6841/MAX6843
push-pull RESET output no longer sinks current; it
becomes an open circuit. Therefore, high-impedance
CMOS-logic inputs connected to RESET can drift to
undetermined voltages. This presents no problem in
most applications, because most P and other circuitry
are inoperative with VCC lower than 0.55V. However, in
applications in which RESET must be valid down to 0,
adding a pulldown resistor to RESET causes any stray
leakage currents to flow to ground, holding RESET low
(Figure 3). R3’s value is not critical; 200k
is large
enough not to load RESET and small enough to pull
RESET to ground.
A 200k
pullup resistor to VCC is also recommended
for the MAX6841/MAX6842/MAX6844 if push-pull
RESET is required to remain valid for VCC
≤ 0.75V.
Interfacing to Ps with Bidirectional
Reset Pins
Because the RESET output on the MAX6842/MAX6845
is open drain, these devices interface easily with Ps
that have bidirectional reset pins. Connecting the P
supervisor’s RESET output directly to the P’s RESET
pin with a single pullup resistor allows either device to
assert reset (Figure 4).
Ultra-Low-Voltage P Reset Circuits and
Voltage Detectors
6
_______________________________________________________________________________________
MAXIMUM TRANSIENT DURATION
vs. OVERDRIVE
OVERDRIVE VTH - VCC (mV)
MAXIMUM
TRANSIENT
DURATION
(
s)
10
150
200
250
300
350
400
450
500
550
600
100
1
100
RESET OCCURS ABOVE THIS LINE
Figure 2. Maximum Transient Duration vs. Overdrive
MAX6841
MAX6843
VCC
RESET
GND
R3
Figure 3. RESET Valid to VCC = 0
MAX6842
MAX6845
VCC
RESET
GND
VCC
RESET
INPUT
GND
P
Figure 4. Interfacing to Microprocessors with Bidirectional
Reset I/0
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6841HUKD0+T | Ultra-Low-Voltage µP Reset Circuits and Voltage Detectors |
| MAX6841HUKD3+T | Ultra-Low-Voltage µP Reset Circuits and Voltage Detectors |
| MAX6842DUKD0+ | Ultra-Low-Voltage µP Reset Circuits and Voltage Detectors |
| MAX6842DUKD0+T | Ultra-Low-Voltage µP Reset Circuits and Voltage Detectors |
| MAX6842DUKD3+T | Ultra-Low-Voltage µP Reset Circuits and Voltage Detectors |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6841HUKD0+ | 制造商:Maxim Integrated Products 功能描述:- Cut Tape Product |
| MAX6841HUKD0+T | 功能描述:监控电路 Single uPower Reset Circuit RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6841HUKD0-T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6841HUKD1 | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX6841HUKD1+ | 制造商:Maxim Integrated Products 功能描述:PROCESSOR SUPERVISOR 1.313V 8.1UA 5PIN SOT-23 - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。