- 您现在的位置：买卖IC网 > PDF目录13279 > MAX6871ETJ+T (Maxim Integrated Products)IC SEQUENCE/SUPERVISOR 32TQFN PDF资料下载
参数资料
| 型号： | MAX6871ETJ+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 10/51页 |
| 文件大小： | 0K |
| 描述： | IC SEQUENCE/SUPERVISOR 32TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 序列发生器 |
| 监视电压数目： | 4 |
| 输出： | 开路漏极，推挽式 |
| 复位： | 高有效/低有效 |
| 复位超时： | 可调节/可选择 |
| 电压 - 阀值： | 5 种可调阀值电压 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页
EEPROM-Programmable Hex/Quad
Power-Supply Sequencers/Supervisors with ADC
Pin Description (continued)
PIN
MAX6870 MAX6871
NAME
FUNCTION
High Voltage Input 1. Configure IN1 to detect voltage thresholds from +2.5V to +13.2V in 50mV
30
30
IN1
increments or +1.25V to +7.625V in 25mV increments. For improved noise immunity, bypass
IN1 to GND with a 0.1μF capacitor installed as close to the device as possible.
Reference Voltage Input. Configure the MAX6870/MAX6871 to use either an internal reference
31
31
REFIN
or external reference (see Table 9). When configured for an internal reference, leave REFIN
unconnected. When configured for an external reference, connect a +1.225V to +1.275V
reference to REFIN.
Programmable Output 1. Configurable active-high, active-low, open-drain, weak pullup, or
32
2
PO1
charge-pump output. PO1 pulls low with a weak 10μA internal current sink for +1V < V ABP
< V UVLO . PO1 assumes its programmed conditional output state when ABP exceeds UVLO.
—
—
EP
Exposed Paddle. Exposed paddle is internally connected to GND.
Detailed Description
The MAX6870/MAX6871 EEPROM-configurable, multi-
voltage supply sequencers/supervisors monitor several
voltage-detector inputs, two auxiliary inputs and four
general-purpose logic inputs, and feature programma-
ble outputs for highly-configurable, power-supply
sequencing applications. The MAX6870 features six
voltage-detector inputs and eight programmable out-
puts, while the MAX6871 features four voltage-detector
inputs and five programmable outputs. Manual reset
and margin disable inputs simplify board-level testing
during the manufacturing process. The MAX6870/
MAX6871 feature an accurate internal 1.25V reference.
For greater accuracy, connect an external +1.25V ref-
erence to REFIN.
All voltage detectors provide two configurable thresh-
olds for undervoltage/overvoltage or dual undervoltage
detection. One high-voltage input (IN1) provides detec-
tor threshold voltages from +1.25V to +7.625V in 25mV
increments or +2.5V to +13.2V in 50mV increments.
A bipolar input (IN2) provides detector threshold volt-
ages from ±1.25V to ±7.625V in 25mV increments, or
±2.5V to ±15.25V in 50mV increments. Positive inputs
(IN3 – IN6) provide detector threshold voltages from
+0.5V to +3.05V in 10mV increments, or +1.0V to +5.5V
in 20mV increments.
An internal 10-bit ADC monitors the voltage-detector
inputs and two auxiliary inputs through a multiplexer
that automatically sequences through all inputs every
200ms. The host controller communicates with the
MAX6870/MAX6871s ’ internal 4kb user EEPROM,
configuration EEPROM, configuration registers, ADC
registers, and fault registers through an SMBus/I 2 C-
compatible serial interface (see Figure 1).
Programmable output options include active-high,
active-low, open-drain, weak pullup, push-pull, and
charge pump. Select the charge-pump output feature
to drive n-channel FETs for power-supply sequencing
(see the Applications Information section). The outputs
swing between 0 and (V ABP + 5V) when configured for
charge-pump operation.
Program each output to assert on any voltage-detector
input, general-purpose logic input, watchdog timer,
manual reset, or other output stages. Programmable
timing-delay blocks configure each output to wait
between 25μs and 1600ms before deasserting. A fault
register logs the conditions that caused each output to
assert (undervoltage, overvoltage, manual reset, etc.).
The MAX6870/MAX6871 feature two watchdog timers,
adding flexibility. Program each watchdog timer to assert
one or more programmable outputs. Program each
10
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| GCA36DTMT-S273 | CONN EDGECARD 72POS R/A .125 SLD |
| MAX634CPA | IC REG INV FLYBK ADJ 0.15A 8DIP |
| ADP121-AUJZ28R7 | IC REG LDO 2.8V .15A TSOT-23-5 |
| RCM36DSEH-S243 | CONN EDGECARD 72POS .156 EYELET |
| 500R07N3R3CV4T | CAP CER 3.3PF 50V NP0 0402 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6872ETJ | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6872ETJ+ | 功能描述:监控电路 EEPROM-Prog Hex Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6872ETJ+T | 功能描述:监控电路 EEPROM-Prog Hex Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6872ETJ-T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6873ETJ | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。