- 您现在的位置：买卖IC网 > PDF目录13297 > MAX6873ETJ+T (Maxim Integrated Products)IC SEQUENCE/SUPERVISOR 32TQFN PDF资料下载
参数资料
| 型号： | MAX6873ETJ+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 12/48页 |
| 文件大小： | 0K |
| 描述： | IC SEQUENCE/SUPERVISOR 32TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 序列发生器 |
| 监视电压数目： | 4 |
| 输出： | 开路漏极，推挽式 |
| 复位： | 高有效/低有效 |
| 复位超时： | 可调节/可选择 |
| 电压 - 阀值： | 5 种可调阀值电压 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页当前第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
EEPROM-Programmable, Hex/Quad,
Power-Supply Sequencers/Supervisors
Program each output to assert on any voltage-detector
input, general-purpose logic input, watchdog timer,
manual reset, or other output stages. Programmable
timing-delay blocks configure each output to wait
between 25μs and 1600ms before deasserting. A fault
register logs the conditions that caused each output to
assert (undervoltage, overvoltage, manual reset, etc.).
The MAX6872/MAX6873 feature two watchdog timers,
adding flexibility. Program each watchdog timer to assert
one or more programmable outputs. Program each
watchdog timer to clear on a combination of one GPI_
input and one programmable output, one of the GPI_
inputs only, or one of the programmable outputs only.
The initial and normal watchdog timeout periods are
independently programmable from 6.25ms to 102.4s.
A virtual diode-ORing scheme selects the input that pow-
ers the MAX6872/MAX6873. The MAX6872/MAX6873
derive power from IN1 if V IN1 > +6.5V or from the highest
voltage on IN3–IN6 if V IN1 < +2.7V. The power source
cannot be determined if +4V < V IN1 < +6.5V and one
of V IN3 through V IN6 > +2.7V. The programmable out-
puts maintain the correct programmed logic state for
V ABP > V UVLO . One of IN3 through IN6 must be
greater than +2.7V or IN1 must be greater than +4V for
device operation.
Powering the MAX6872/MAX6873
The MAX6872/MAX6873 derive power from the positive
The MAX6872/MAX6873 also generate a digital supply
voltage (DBP) for the internal logic circuitry and the
EEPROM; bypass DBP to GND with a 1μF ceramic
capacitor installed as close to the device as possible.
The nominal DBP output voltage is +2.55V. Do not use
DBP to provide power to external circuitry.
Inputs
The MAX6872/MAX6873 contain multiple logic and volt-
age-detector inputs. Each voltage-detector input is
simultaneously monitored for primary and secondary
thresholds. The primary threshold must be an under-
voltage threshold. The secondary threshold may be an
undervoltage or overvoltage threshold. Table 1 summa-
rizes these various inputs.
Set the primary and secondary threshold voltages for
each voltage-detector input with registers 00h–0Bh.
Each primary threshold voltage must be an undervolt-
age threshold. Configure each secondary threshold
voltage as an undervoltage or overvoltage threshold
(see register 0Ch). Set the threshold range for each
voltage detector with register 0Dh.
High-Voltage Input (IN1)
IN1 offers threshold voltages of +2.5V to +13.2V in
50mV increments, or +1.25V to +7.625V in 25mV incre-
ments. Use the following equations to set the threshold
voltages for IN1:
x = TH
x = TH
voltage-detector inputs: IN1 or IN3–IN6. A virtual diode-
ORing scheme selects the positive input that supplies
power to the device (see the Functional Diagram ). IN1
must be at least +4V or one of IN3–IN6 (MAX6872)/
IN3–IN4 (MAX6873) must be at least +2.7V to ensure
device operation. An internal LDO regulates IN1 down
to +5.4V.
V ? 2.5 V
0 . 05 V
V ? 1.25 V
0 . 025 V
for + 2 . 5 V to + 13 . 2 V range
for + 1 . 25 V to + 7 . 625 V range
The highest input voltage on IN3 –IN6 (MAX6872)/
IN3–IN4 (MAX6873) supplies power to the device, unless
V IN1 ≥ +6.5V, in which case IN1 supplies power to the
device. For +4V < V IN1 < +6.5V and one of V IN3 through
V IN6 > +2.7V, the input power source cannot be deter-
mined due to the dropout voltage of the LDO. Internal
hysteresis ensures that the supply input that initially pow-
ered the device continues to power the device when
multiple input voltages are within 50mV of each other.
ABP powers the analog circuitry; bypass ABP to GND
with a 1μF ceramic capacitor installed as close to the
device as possible. The internal supply voltage, mea-
sured at ABP, equals the maximum of IN3 –IN6
where V TH is the desired threshold voltage and x is the
decimal code for the desired threshold ( Table 2). For
the +2.5V to +13.2V range, x must equal 214 or less,
otherwise the threshold exceeds the maximum operat-
ing voltage of IN1.
Bipolar-Voltage Input (IN2)
IN2 offers negative thresholds from -2.5V to -15.25V in
50mV increments, or from -1.25V to -7.625V in 25mV
increments. Alternatively, IN2 offers positive thresholds
from +2.5V to +15.25V in 50mV increments, or +1.25V
to +7.625V in 25mV increments. Use the following
equations to set the threshold voltages for IN2:
(MAX6872)/IN3–IN4 (MAX6873) if V IN1 = 0, or equals
+5.4V when V IN1 > +6.5V. Do not use ABP to provide
power to external circuitry.
x =
? ( V TH ? 2 . 5 V
0 . 05 V
)
for ? 2 . 5 V to ? 15 . 25 V range
12
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| GEM08DTAT-S273 | CONN EDGECARD 16POS R/A .156 SLD |
| ESM22DRMD-S664 | CONN EDGECARD 44POS .156 WW |
| EGM22DRMD-S664 | CONN EDGECARD 44POS .156 WW |
| MIC2940A-12WU | IC REG LDO 12V 1.25A TO-263 |
| EL7556DCMZ | IC REG BUCK SYNC ADJ 6A 28SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6874ETJ | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6874ETJ+ | 功能描述:监控电路 EEPROM-Prog Hex Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6874ETJ+T | 功能描述:监控电路 EEPROM-Prog Hex Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6874ETJ-T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6874TCC+ | 制造商:Maxim Integrated Products 功能描述: |
发布紧急采购，3分钟左右您将得到回复。