- 您现在的位置：买卖IC网 > PDF目录13302 > MAX6874ETJ+T (Maxim Integrated Products)IC SEQUENCE/SUPERVISOR 32TQFN PDF资料下载
参数资料
| 型号： | MAX6874ETJ+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 30/40页 |
| 文件大小： | 0K |
| 描述： | IC SEQUENCE/SUPERVISOR 32TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 序列发生器 |
| 监视电压数目： | 6 |
| 输出： | 开路漏极，推挽式 |
| 复位： | 高有效/低有效 |
| 复位超时： | 可调节/可选择 |
| 电压 - 阀值： | 8 种可选阀值组合 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页当前第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
EEPROM-Programmable, Hex/Quad,
Power-Supply Sequencers/Supervisors
For the configuration EEPROM, valid address pointers
range from 8000h to 8045h. Registers 8046h to 804Fh
are reserved and should not be overwritten. Register
addresses from 8050h to 80FFh return a NACK from
the MAX6874/MAX6875. When using the block write
protocol, the address pointer automatically increments
after each data byte, except when the address pointer
is already at 8045h. If the address pointer is already
8045h, and more data bytes are being sent, these sub-
sequent bytes overwrite address 8045h repeatedly,
leaving only the last data byte sent stored at this regis-
ter address.
For the user EEPROM, valid address pointers range
from 8100h to 81FFh and 8200h to 82FFh. Block write
and block read protocols allow the address pointer to
reset (to 8100h or 8200h) when attempting to write or
read beyond 81FFh or 82FFh.
Configuration EEPROM
The configuration EEPROM addresses range from 8000h
to 8045h. Write data to the configuration EEPROM to
automatically set up the MAX6874/MAX6875 upon power-
up. Data transfers from the configuration EEPROM to the
configuration registers when ABP exceeds UVLO during
power-up or after a software reboot. After ABP exceeds
UVLO, an internal 1MHz clock starts after a 5μs delay,
and data transfer begins. Data transfer disables access
to the configuration registers and EEPROM. The data
transfer from EEPROM to configuration registers takes
3.5ms (max). Read configuration EEPROM data at any
Table 17. Register Map
time after power-up or software reboot. Write commands
to the configuration EEPROM are allowed at any time
after power-up or software reboot, unless the configura-
tion lock bit is set (see Table 20). The maximum cycle
time to write a single byte is 11ms (max).
User EEPROM
The 512 byte user EEPROM addresses range from
8100h to 82FFh (see Figure 7). Store software-revision
data, board-revision data, and other data in these reg-
isters. The maximum cycle time to write a single byte is
11ms (max).
Configuration Register Bank and EEPROM
The configuration registers can be directly modified by
the serial interface without modifying the EEPROM after
the power-up procedure terminates and the configura-
tion EEPROM data has been loaded into the configura-
tion register bank. Use the write byte or block write
protocols to write directly to the configuration registers.
Changes to the configuration registers take effect
immediately and are lost upon power removal.
At device power-up, the register bank loads configura-
tion data from the EEPROM. Configuration data may be
directly altered in the register bank during application
development, allowing maximum flexibility. Transfer the
new configuration data, byte by byte, to the configura-
tion EEPROM with the write byte protocol. The next
device power-up or software reboot automatically loads
the new configuration.
REGISTER
ADDRESS
00h
01h
02h
03h
04h
05h
06h
07h
08h
09h
0Ah
EEPROM
MEMORY
ADDRESS
8000h
8001h
8002h
8003h
8004h
8005h
8006h
8007h
8008h
8009h
800Ah
READ/
WRITE
R/W
R/W
R/W
R/W
R/W
R/W
—
—
—
—
—
DESCRIPTION
IN1 undervoltage detector threshold (Table 2).
IN2 undervoltage detector threshold (Table 3).
IN3 undervoltage detector threshold (Table 4).
IN4 undervoltage detector threshold (Table 4).
IN5 undervoltage detector threshold (MAX6874 only) (Table 4).
IN6 undervoltage detector threshold (MAX6874 only) (Table 4).
Not used.
Not used.
Not used.
Not used.
Not used.
30
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| EMC25DREI-S93 | CONN EDGECARD 50POS .100 EYELET |
| RBC40DRAN-S734 | CONN EDGECARD 80POS .100 R/A PCB |
| 63TXW820MEFC10X60 | CAP ALUM 820UF 63V 20% RADIAL |
| 100ZLJ390MGC16X25 | CAP ALUM 390UF 100V 20% RADIAL |
| 100ZLJ390M16X25 | CAP ALUM 390UF 100V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6874TCC+ | 制造商:Maxim Integrated Products 功能描述: |
| MAX6875ETJ | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6875ETJ+ | 功能描述:监控电路 EEPROM-Prog Quad Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6875ETJ+T | 功能描述:监控电路 EEPROM-Prog Quad Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6875ETJ-T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。