- 您现在的位置：买卖IC网 > PDF目录1845 > MAX6884ETP+ (Maxim Integrated Products)IC SUPERVISOR PWR SPL 20-TQFN PDF资料下载
参数资料
| 型号： | MAX6884ETP+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 13/34页 |
| 文件大小： | 0K |
| 描述： | IC SUPERVISOR PWR SPL 20-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 60 |
| 类型： | 多压监控器 |
| 监视电压数目： | 6 |
| 输出： | 开路漏极，推挽式 |
| 复位： | 高有效/低有效 |
| 复位超时： | 可调节/可选择 |
| 电压 - 阀值： | 6 种可选阀值组合 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-WQFN 裸露焊盘 |
| 供应商设备封装： | 20-TQFN-EP（5x5） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
EEPROM-Programmable, Hex
Power-Supply Supervisory Circuits
X = TH
X = TH
Powering the MAX6884/MAX6885
The MAX6884/MAX6885 derive power from the voltage-
detector inputs: IN1–IN4 or through an externally sup-
plied V CC . A virtual diode-ORing scheme selects the
positive input that supplies power to the device (see the
Functional Diagram ). The highest input voltage on
IN1–IN4 supplies power to the device. One of V IN1 –V IN4
must be at least 2.7V to ensure proper operation.
Internal hysteresis ensures that the supply input that initially
powered the device continues to power the device when
multiple input voltages are within 50mV of each other.
V CC powers the analog circuitry and is the bypass con-
nection for the MAX6884/MAX6885 internal supply.
Bypass V CC to GND with a 1μF ceramic capacitor
installed as close to the device as possible. The internal
supply voltage, measured at V CC , equals the maximum
of IN1–IN4. If V CC is externally supplied, V CC must be at
least 200mV higher than any voltage applied to IN–IN4
and V CC must be brought up first. V CC always powers
the device when all IN_ are factory set as “ADJ.” Do not
use the internally generated V CC to provide power to
external circuitry. Externally supply power through V CC .
To externally supply power through V CC :
1) Apply a voltage to only one of V CC (2.7V to 5.5V) or
IN1–IN4 (2.7V to 5.8V).
2) Program the internal/external V CC Power EEPROM at
96h, Bit[5] = 1 (see Table 2).
3) Power down the device.
Subsequent power-ups and software reboots require an
externally supplied V CC to ensure the device is fully
operational.
Table 2. Internal/External V CC
ADC (MAX6884 Only)
An internal 10-bit ADC (MAX6884 only) converts volt-
ages at IN1–IN4, AUXIN, and V CC through a multiplexer
that automatically sequences through all inputs every
200ms. Registers 18h to 27h store the ADC data (see
Table 3). Read the ADC data from the MAX6884 with
the serial interface. The ADC has no effect on program-
mable outputs RESET , UV / OV , or WDO .
Inputs
The MAX6884/MAX6885 offer the following inputs: volt-
age-detector inputs IN1 –IN4, auxiliary input AUXIN
(MAX6884 only), manual reset input MR , margin input
MARGIN , and reference input REFIN (MAX6884 only).
IN1–IN6
The MAX6884/MAX6885 offer six voltage-detector inputs:
IN1–IN6. Each voltage-detector input offers a program-
mable primary undervoltage threshold and a secondary
undervoltage/overvoltage threshold. Program thresholds
from 0.5V to 3.05V in 10mV increments, 1.0V to 5.8V in
20mV increments, or from 0.1667V to 1.0167V in 3.3mV
increments. Use the following equations to program
thresholds in the appropriate registers:
V ? 1V
0 . 02 V
for 1V to 5.8V range in 20mV increments (program bits
R0Fh[5:0]).
V ? 0.5V
0 . 01 V
for 0.5V to 3.05V range in 10mV increments (program
X = TH
REGISTER
ADDRESS
EEPROM
MEMORY
ADDRESS
BIT
RANGE
DESCRIPTION
bits R0Fh[5:0]).
V ? 0.1667V
0 . 0033 V
1 = V CC Powered
[5]
0 = IN1–IN4 or V CC
Powered
for 0.1667V to 1.0167V in 3.3mV increments (see the
External Voltage-Divider section).
16h
96h
[2]
[4]
[6]
Not Used
Not Used
Not Used
where V TH is the desired threshold voltage and X is the
decimal code for the desired threshold (see Table 4). To
set a threshold for the 1V to 5.8V range, X must equal 240
or less. Set the secondary threshold for an undervoltage
The MAX6884/MAX6885 also generate a digital supply
voltage (DBP) for the internal logic circuitry and the
EEPROM. Bypass DBP to GND with a 1μF ceramic
capacitor installed as close to the device as possible.
The nominal DBP output voltage is 2.55V. Do not use
DBP to provide power to external circuitry.
or overvoltage threshold by programming bits R0Eh[5:0].
To achieve thresholds in between the 10mV and 20mV
steps or to monitor voltages higher than 5.8V, program a
voltage-detector input for high impedance through bits
R10h[5:0] and add a resister voltage-divider (see the
External Voltage-Divider section).
______________________________________________________________________________________
13
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6886ETP+T | IC SUPERVISOR HEX 20-TQFN |
| MAX6887RETE+ | IC SUPERVISOR HEX 16-TQFN |
| MAX6889ETJ+T | IC SEQUENCE/SUPERVISOR 32TQFN |
| MAX688ESA+T | IC REG LDO 3.3V 1A 8-SOIC |
| MAX6894ETI+ | IC SEQUENCE/SUPERVISOR 28TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6884ETP+ | 功能描述:监控电路 EEPROM-Prog Hex Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6884ETP+T | 功能描述:监控电路 EEPROM-Prog Hex Power-Sup Sequencer RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6884ETP-T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6884EVCMOD2 | 功能描述:监控电路 Programmers, Development Systems RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6884EVKIT | 功能描述:监控电路 Programmers, Development Systems RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。