- 您现在的位置：买卖IC网 > PDF目录1845 > MAX6886ETP+T (Maxim Integrated Products)IC SUPERVISOR HEX 20-TQFN PDF资料下载
参数资料
| 型号： | MAX6886ETP+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 8/13页 |
| 文件大小： | 0K |
| 描述： | IC SUPERVISOR HEX 20-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 多压监控器 |
| 监视电压数目： | 6 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 低有效 |
| 复位超时： | 可调节/可选择 |
| 电压 - 阀值： | 6 种可选阀值组合 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-WQFN 裸露焊盘 |
| 供应商设备封装： | 20-TQFN-EP（5x5） |
| 包装： | 带卷 (TR) |
Pin-Selectable, Hex Power-Supply
Supervisory Circuit
Detailed Description
The MAX6886 pin-selectable, multivoltage supply
supervisor monitors six voltage-detector inputs and one
watchdog input. RESET asserts when any of the config-
ured input thresholds have been reached, MR is assert-
ed, or the watchdog timer expires. MARGIN allows a
system to be tested without RESET being asserted.
Logic inputs TH0–TH4 select 1 of 32 threshold sets for
inputs IN1 –IN6 (see Table 2, Threshold Options).
Inputs in Table 2 that contain ADJ for inputs allow
external resistor voltage-dividers to be connected to
create additional thresholds.
RESET is an open-drain acitve-low output and asserts
when MR is low, the watchdog timer expires, or any
voltage at IN1–IN6 falls below its respective threshold.
The default RESET time delay is 200ms and custom
timeout periods are set by connecting an external
capacitor from SRT to GND. The default watchdog nor-
mal and initial timeout periods are 1.6s and 102.4s,
respectively. The normal and initial watchdog timeout
periods can be adjusted by connecting an external
capacitor from SWT to GND.
Powering the MAX6886
The MAX6886 derives power from the voltage-detector
inputs IN1–IN4 or through an externally supplied V CC .
A virtual diode-ORing scheme selects the positive input
that supplies power to the device (see the Functional
Diagram). The highest input voltage on IN1–IN4 sup-
plies power to the device. One of IN1–IN4 must be at
least 2.7V to ensure proper operation.
Internal hysteresis ensures that the supply input that
initially powered the device continues to power the
device when multiple input voltages are within 50mV of
each other.
V CC powers the analog circuitry and is the bypass con-
Inputs
The MAX6886 contains multiple logic and voltage-
detector inputs. Each voltage-detector input is moni-
tored for undervoltage thresholds.
Voltage-Detector Inputs (IN_)
The MAX6886 offers several monitor options with both
pin-selectable and adjustable reset thresholds. The
threshold voltage at each adjustable IN_ input is typi-
cally 0.6V. To monitor a voltage >0.6V, connect a resis-
tor-divider network to the circuit as shown in Figure 1.
V IN_TH = V TH (R 1 + R 2 ) / R 2 (Equation 1)
where V IN_TH is the desired reset threshold voltage for
the respective IN_ and V TH is the input threshold (0.6V).
Resistors R 1 and R 2 can have very high values to mini-
mize current consumption due to low-leakage currents.
Set R 2 to some conveniently high value (10k ? , for
example) and calculate R 1 based on the desired reset
threshold voltage, using the following formula:
R 1 = R 2 x (V IN_TH /V TH - 1)
Threshold Logic Inputs (TH0–TH4)
The TH0 –TH4 logic inputs select the undervoltage
thresholds and tolerance of the IN1–IN6 voltage-detec-
tor inputs. TH0–TH4 define 32 unique options for the
supervisor functionality. Connect the respective TH_ to
GND for a logic 0 or to DBP for a logic 1. Tables 1 and
2 show the 32 unique threshold options available. TH4
sets the threshold tolerance of the undervoltage thresh-
old. A logic 1 selects a 5% supply tolerance and a
logic 0 selects a 10% supply tolerance. The MAX6886
logic determines which thresholds should be used for
V IN
nection for the MAX6886 internal supply. Bypass V CC
to GND with a 1μF ceramic capacitor installed as close
to the device as possible. The internal supply voltage,
measured at V CC , equals the maximum of IN1–IN4. If
V CC is externally supplied, V CC must be at least 200mV
higher than any voltage applied to IN1–IN4 and V CC
must be brought up first. V CC always powers the
device when all IN_ are factory set as “ADJ.” Do not
use the internally generated V CC to provide power to
external circuitry.
The MAX6886 generates a digital supply voltage at DBP
for the internal logic circuitry and RESET . Bypass DBP
to GND with a 1μF ceramic capacitor installed as close
to the device as possible. The nominal DBP output volt-
R1
R2
IN_
0.6V
MAX6886
age is 2.55V. Do not use DBP to provide power to exter-
nal circuitry.
Figure 1. Adjusting the Monitored Threshold
8
_______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6887RETE+ | IC SUPERVISOR HEX 16-TQFN |
| MAX6889ETJ+T | IC SEQUENCE/SUPERVISOR 32TQFN |
| MAX688ESA+T | IC REG LDO 3.3V 1A 8-SOIC |
| MAX6894ETI+ | IC SEQUENCE/SUPERVISOR 28TQFN |
| MAX6898PALT+T | IC SEQUENCE/SUPERVISOR 6UDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6887AETE | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6887AETE+ | 功能描述:监控电路 Hex Power-Supply Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6887AETE+T | 功能描述:监控电路 Hex Power-Supply Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6887AETE-T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6887BETE | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。