- 您现在的位置：买卖IC网 > PDF目录20747 > MAX689CSA (Maxim Integrated)IC REG LDO 3V 1A 8-SOIC PDF资料下载
参数资料
| 型号： | MAX689CSA |
| 厂商： | Maxim Integrated |
| 文件页数： | 8/12页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 3V 1A 8-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 100 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 3V |
| 输入电压： | 最高 11V |
| 电压 - 压降（标准）： | 0.04V @ 200mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 1A |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 管件 |
High-Accuracy, Low-Dropout
Linear Regulators
( 50 mV ) x h FE(MIN)
is given by I LOAD(MAX) = 10mA x h FE(MIN) . The tran-
sistor’s rated power dissipation must exceed the actual
power dissipated in the transistor. The power dissipat-
ed (PD) equals the maximum load current (I LOAD(MAX) )
times the maximum input to output voltage differential:
PD = I LOAD(MAX) x (V IN(MAX) - V OUT ). The rated tran-
sistor collector current must exceed the maximum load
current. Suitable transistors include the Zetex FZT749,
and the 2N2907A (see Table 2).
Base-Current Limiting
A comparator monitors the voltage across the external
base-current-limiting resistor (between BASE and
BLIM). This sets the maximum base current. If BASE
and BLIM are shorted, base current is limited nominally
to 20mA due to an internal 5 ? resistor in series with the
external resistance. Choose the base-current-limiting
resistor, R B , so the drop across it at rated load is
approximately 50mV.
R B = ? 5 ?
I LOAD(MAX)
The base drive is controlled so the voltage on BLIM is
limited to 100mV below the voltage on BASE; with a
50mV nominal drop across R B + 5 ? , base-current drive
is limited to twice the nominal. This limits base current
when the external PNP is heavily saturated, such as
when the regulator is in dropout due to low input volt-
age. In addition, if the external PNP’s h FE is defined
within reasonable limits, base-current control effectively
limits output current without a dropout voltage penalty.
________________Capacitor Selection
Bypass Capacitor (C1)
Connect a bypass capacitor from IN to GND. 4.7μF
makes the circuit insensitive to layout, and is sufficient
for any load. Smaller values may be used—down to
0.33μF—with low-ESR capacitors, good board layout,
and a low-impedance incoming supply.
Connect the bypass capacitor directly between pins 1
and 4 of the IC, using short leads. Connect the emitter
of the PNP transistor directly to the bypass capacitor
using a very short trace.
Output Capacitor (C2)
The output filter capacitor must be at least 10μF. For
currents above 100mA, use 1μF of capacitance for
every 10mA of load current (e.g., 20μF for 200mA load,
50μF for 500mA). Low-ESR capacitors give best stabili-
ty and transient response. Ensure that the capacitor’s
ESR is less than 1% of the load resistance. See Table 2
for a list of manufacturers. Sanyo OS-CON capacitors
are recommended for applications operating at temper-
atures below 0°C.
Compensation Capacitor (C3)
Connect a compensation capacitor from CC to GND.
10nF is recommended, although higher values (up to
100nF) may also be used. Higher C3 values eliminate
power-on overshoot, but extend power-up times.
Current flowing into or out of CC causes the regulator’s
reference voltage to change, resulting in shifted output
voltage and trip thresholds. Use non-polarized capaci-
tors (e.g., ceramic, polyester, etc.) to keep leakage cur-
rents below 25nA. Aluminum and tantalum electrolytic
capacitors are unsuitable because of their high leakage
currents.
__________________Power-Fail Output
The PFO output trips when V OUT is 170mV below nomi-
nal V OUT at I BASE = 1mA. PFO sources and sinks cur-
rent in the MAX687, but is an open drain in the
MAX688/MAX689 and only sinks current. When shut
down, PFO is always low regardless of the voltage at
OUT. Leave PFO open if it is not used.
8
_______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX16823ATE/V+T | IC LED DRIVER HIGH BRIGHT 16WQFN |
| MAX16823ATE+T | IC LED DRIVR HIGH BRIGHT 16-TQFN |
| MAX689CPA | IC REG LDO 3V 1A 8-DIP |
| EBC25DRES | CONN EDGECARD 50POS .100 EYELET |
| NCV86602D33R2G | IC REG LDO 3.3V .15A 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX689CSA+ | 功能描述:低压差稳压器 - LDO High-Accuracy LDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX689CSA+T | 功能描述:低压差稳压器 - LDO High-Accuracy LDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX689CSA-T | 功能描述:低压差稳压器 - LDO High-Accuracy LDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX689CUA | 功能描述:低压差稳压器 - LDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX689CUA-T | 功能描述:低压差稳压器 - LDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。