参数资料
| 型号： | MAX6934AQH+TD |
| 厂商： | Maxim Integrated |
| 文件页数： | 8/16页 |
| 文件大小： | 0K |
| 描述： | IC DRVR VFD TUBE SRL 44PLCC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 500 |
| 显示器类型： | 真空荧光 (VF) |
| 接口： | 4 线串行 |
| 电流 - 电源： | 2mA |
| 电源电压： | 8 V ~ 76 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 44-LCC（J 形引线） |
| 供应商设备封装： | 44-PLCC（16.59x16.59） |
| 包装： | 带卷 (TR) |
27-, 28-, and 32-Output, 76V,
Serial-Interfaced VFD Tube Drivers
Each driver output is a slew-rate controlled CMOS
push-pull switch driving between V BB and GND
(MAX6922) or V BB and V SS (MAX6932/MAX6933/
MAX6934). The output rise time is always slower than
the output fall time to avoid shoot-through currents dur-
ing output transitions. The output slew rates are slow
enough to minimize EMI, yet are fast enough so as not
to impact the typical 100μs digit multiplex period and
affect the display intensity.
Initial Power-Up and Operation
An internal reset circuit clears the internal registers on
power-up. All outputs and the interface output DOUT
(MAX6922/MAX6932/MAX6934 only) initialize low
regardless of the initial logic levels of the CLK, DIN,
BLANK, and LOAD inputs.
4-Wire Serial Interface
These driver ICs use a 4-wire serial interface with three
inputs (DIN, CLK, LOAD) and a data output (DOUT,
MAX6922/MAX6932/MAX6934 only). This interface is
used to write data to the ICs (Figure 4) (Table 1). The
serial interface data word length is 32 bits for the
MAX6922/MAX6934, 27 bits for the MAX6932, and 28
bits for the MAX6933.
The functions of the four serial interface pins are:
? CLK input is the interface clock, which shifts data
into the shift register on its rising edge.
? LOAD input passes data from the shift register to the
output latch when LOAD is high (transparent latch),
and latches the data on LOAD’s falling edge.
? DIN is the interface data input, and must be stable
when it is sampled on the rising edge of CLK.
? DOUT is the interface data output, which shifts data
out from the shift register on the rising edge of CLK.
Data at DIN is propagated through the shift register
and appears at DOUT (n CLK cycles + t DO ) later,
where n is the number of drivers in the IC.
A fifth input, BLANK, can be taken high to force the out-
puts low, without altering the contents of the output latch-
es. When the BLANK input is low, the outputs follow the
state of the output latches. A common use of the BLANK
input is PWM intensity control.
The BLANK input’s function is independent of the oper-
ation of the serial interface. Data can be shifted into the
serial interface shift register and latched regardless of
the state of BLANK.
Writing Device Registers Using
the 4-Wire Serial Interface
The MAX6922/MAX6932/MAX6933/MAX6934 are nor-
mally written using the following sequence:
1) Take CLK low.
2) Clock n bits of data in order D n-1 first to D0 last into
DIN, observing the data setup and hold times.
3) Load the n output latches with a falling edge on LOAD,
where n is 27 for the MAX6932, 28 for the MAX6933,
and 32 for the MAX6922 and MAX6934.
LOAD may be high or low during a transmission. If
LOAD is high, then the data shifted into the shift regis-
ter at DIN appears at the OUT0 to OUT n-1 outputs.
CLK and DIN may be used to transmit data to other
peripherals. Activity on CLK always shifts data into the
shift register. However, the output latches only update
on the rising edge of LOAD, and the last n bits of data
t CSW
LOAD
t CL
t CH
t CP
t CSH
CLK
t DH
t DS
DIN
Dn-1
Dn-2
D1
D0
t DO
DOUT
Figure 4. 4-Wire Serial Interface Timing Diagram
Dn-1
8
_______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6950EEE+T | IC DRVR DSPL LED SRL 16-QSOP |
| MAX6952EAX+T | IC DRVR DSPL LED 36-SSOP |
| MAX6953EAX+T | IC DRVR DSPL LED 36-SSOP |
| MAX6954AAX | IC DRIVER LED SEG 14/16 36-SSOP |
| MAX6955ATL+T | IC DRVR DSPL LED 40-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6934ATH | 功能描述:VFD驱动器 RoHS:否 制造商:Maxim Integrated 工作电源电压:8 V to 76 V, 3 V to 5.5 V 电源电流:0.9 mA, 700 uA 最大工作温度:+ 125 C 封装 / 箱体:SOIC-20 封装:Tube |
| MAX6934ATH+T | 功能描述:VFD驱动器 RoHS:否 制造商:Maxim Integrated 工作电源电压:8 V to 76 V, 3 V to 5.5 V 电源电流:0.9 mA, 700 uA 最大工作温度:+ 125 C 封装 / 箱体:SOIC-20 封装:Tube |
| MAX6934ATH-T | 功能描述:VFD驱动器 RoHS:否 制造商:Maxim Integrated 工作电源电压:8 V to 76 V, 3 V to 5.5 V 电源电流:0.9 mA, 700 uA 最大工作温度:+ 125 C 封装 / 箱体:SOIC-20 封装:Tube |
| MAX693AC/D | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX693ACPE | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。