- 您现在的位置：买卖IC网 > Datasheet目录341 > MAX6947ATE+T (Maxim Integrated)IC LED DRIVER LINEAR 16-TQFN Datasheet资料下载
参数资料
| 型号： | MAX6947ATE+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 20/24页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVER LINEAR 16-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 恒定电流： | 是 |
| 拓扑： | 开路漏极，PWM |
| 输出数： | 10 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光 |
| 类型 - 次要： | RGB，白色 LED |
| 频率： | 400kHz |
| 电源电压： | 2.25 V ~ 3.6 V |
| 输出电压： | 7V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WFQFN 裸露焊盘 |
| 供应商设备封装： | 16-TQFN（3x3） |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 125°C |
10-Port, Constant-Current LED Driver and
I/O Expander with PWM Intensity Control
Using Stagger with Fewer Ports
The stagger option, when selected, applies to all ports
configured as constant-current outputs. The 10 ports’
PWM cycles are separated to eight evenly spaced start
positions (Figure 3). Optimize phasing when using
fewer than 10 ports as constant-current outputs by allo-
cating the ports with the most appropriate start posi-
tions. If using eight constant-current outputs, choose
P0–P7 because these all have different PWM start posi-
tions. If using four constant-current outputs, choose P0,
P2, P4, P6 or P1, P3, P5, P7 because their PWM start
positions are evenly spaced. In general, choose the
ports that spread the PWM start positions as evenly as
possible. This optimally spreads out the current
demand from the ports’ load supply.
Generating a Shutdown/Run Output
The MAX6946/MAX6947 can use an I/O port to auto-
matically generate a shutdown/run output. The shut-
down/run output is active low when the MAX6946/
MAX6947 are in run mode, hold-off, fade-off, or ramp-
up, and goes high automatically when the devices final-
ly enter shutdown after fade-off. Programming the port’s
output register to value 0x02 puts the output into static
constant-current mode (Table 4). Program the port’s
output current register to half current (Table 6) to mini-
mize operating current. Connect a 220k Ω pullup resis-
tor to this port.
In run mode, the output port goes low, approaching 0V,
as the port’s static constant current saturates trying to
sink a higher current than the 220k Ω pullup resistor can
In shutdown mode, the output goes high impedance
together with any other constant-current outputs. This
output remains low during ramp-up and fade-down
sequences because the current drawn by the 220k Ω
pullup resistor is much smaller than the available output
constant current, even at the lowest fade current step.
Driving Load Currents Higher than 20mA
The MAX6946/MAX6947 can drive loads needing more
than 20mA, like high-current white LEDs, by paralleling
outputs. For example, consider a white LED that
requires 70mA. Drive this LED using the ports P0–P3
connected in parallel (shorted together). Configure
three of the ports for full current (20mA) and configure
the last port for half current (10mA) to meet the 70mA
requirement. Control the four ports simultaneously with
one write access using register 0x0B (Table 1). Note
that because the output ports are current limiting, they
do not need to switch simultaneously to ensure safe
current sharing.
Power-Supply Considerations
The MAX6946/MAX6947 operate with a power-supply
voltage of 2.25V to 3.6V. Bypass the power supply to
GND with a 0.1μF ceramic capacitor as close as possi-
ble to the device.
Chip Information
PROCESS: BiCMOS
source.
Pin Configurations (continued)
TOP VIEW
RST 13
VDD 14
12
11
10
9
8
7
P6
P5
MAX6946
SCL 15
SDA 16
+
MAX6947
6
5
GND
P4
1
2
3
4
TQFN (3mm x 3mm)
() MAX6947 ONLY
20
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6948BGWA+T | IC LED DVR PWM GPIO 25WLP |
| MAX6964ATG+T | IC LED DRIVER LINEAR 24-TQFN |
| MAX6965ATE+T | IC LED DRIVER LINEAR 16-TQFN |
| MAX6967ATE+ | IC LED DRIVER LINEAR 16-TQFN |
| MAX6968AAE+ | IC LED DRIVER LINEAR 16-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6948BGWA+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX6948BGWA+T | 功能描述:LED照明驱动器 High-Efficiency PWM LED Driver RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MAX694C/D | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX694CPA | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX694CPA+ | 功能描述:监控电路 MPU Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。