参数资料
| 型号： | MAX6952EAX+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 14/21页 |
| 文件大小： | 0K |
| 描述： | IC DRVR DSPL LED 36-SSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1,000 |
| 显示器类型： | LED |
| 配置： | 5 x 7（矩阵） |
| 接口： | 4 线串行 |
| 数字或字符： | 4 位数字 |
| 电流 - 电源： | 12mA |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 36-BSOP（0.295"，7.50mm 宽） |
| 供应商设备封装： | 36-SSOP |
| 包装： | 带卷 (TR) |
4-Wire Interfaced, 2.7V to 5.5V,
4-Digit 5 ? 7 Matrix LED Display Driver
Table 15. Memory Mapping of User-Defined Font Register 0x05
ADDRESS CODE
(HEX)
REGISTER
DATA
SPI READ
OR WRITE
FUNCTION
Read 7-bit user-definable font data entry from current font
0x85
0x00 – 0x7F
Read
address. MSB of the register data is clear. Font address
pointer is incremented after the read.
Write 7-bit user-definable font data entry to current font
0x05
0x00 – 0x7F
Write
address. Font address pointer is incremented after the
write.
0x05
0x80 – 0xFF
Write
Write font address pointer with the register data.
Table 16. Font Pointer Address Behavior
FONT POINTER ADDRESS
0x80 to 0xF6
0xF7
0xF8 to 0xFF
ACTION
Valid range to set the font address pointer. Pointer autoincrements after a font data read or
write, while pointer address remains in this range.
Font address resets to 0x80 after a font data read or write to this pointer address.
Invalid range to set the font address pointer. Pointer is set to 0x80 if address.
? If OSC is driven with an accurate frequency, blink
can be used as a seconds counter or similar.
Scan-Limit Register
The scan-limit register sets how many monocolor digits
are displayed, either two or four. A bicolor digit is con-
nected as two monocolor digits.
The multiplexing scheme drives digits 0 and 1 at the
same time, then digits 2 and 3 at the same time. To
increase the effective brightness of the displays, drive
only two digits instead of four. By doing this, the aver-
age segment current doubles, but also doubles the
number of MAX6952s required to drive a given number
of digits.
Because digit 1 is driven at the same time as digit 0
(and digit 3 is driven at the same time as digit 2), only 1
bit is used to set the scan limit. The bit is clear if one or
two digits are to be driven, and set if three or four digits
are to be driven (Table 20). Change the scan-limit
register only when the MAX6952 is in shutdown mode.
Intensity Registers
Display brightness is controlled digitally by four pulse-
width modulators, one for each display digit. Each digit is
controlled by a nibble of one of the two intensity registers,
Intensity10 and Intensity32. The modulator scales the
average segment current in 16 steps from a maximum of
15/16 down to 1/16 of the peak current. The minimum
interdigit blanking time is, therefore, 1/16 of a cycle. The
maximum duty cycle is 15/16. (Tables 21 and 22).
No-Op Register
A write to the no-op register is ignored.
Selecting External Components R SET and
C SET to Set Oscillator Frequency and
Segment Current
The RC oscillator uses an external resistor RSET and an
external capacitor C SET to set the oscillator frequency,
f OSC . The allowed range of f OSC is 1MHz to 8MHz.
R SET also sets the peak segment current. The recom-
mended values of R SET and C SET set the oscillator to
4MHz, which makes the blink frequencies 0.5Hz and
1Hz. The recommended value of R SET also sets the
peak current to 40mA, which makes the segment cur-
rent adjustable from 2.5mA to 37.5mA in 2.5mA steps:
I SEG = K I / R SET mA
f OSC = K F / (R SET ? C SET + C STRAY ) MHz
Where:
K I = 2144
K F = 6000
R SET = external resistor in k ?
C SET = external capacitor in pF
C STRAY = stray capacitance from OSC pin to GND in
pF, typically 2pF
The recommended value of R SET is 53.6k ? and the
recommended value of C SET is 26pF.
14
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6953EAX+T | IC DRVR DSPL LED 36-SSOP |
| MAX6954AAX | IC DRIVER LED SEG 14/16 36-SSOP |
| MAX6955ATL+T | IC DRVR DSPL LED 40-TQFN |
| MAX6956ATL/V+ | IC DRIVER LED PORT 20/28 40WQFN |
| MAX6957ANI | IC DRIVER LED PORT 20/28 28-DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6952EPL | 功能描述:LED显示驱动器 RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| MAX6952EPL+ | 功能描述:LED显示驱动器 MAX6952EPL+ RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| MAX6952EVKIT | 功能描述:LED 照明开发工具 RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
| MAX6953EAX | 功能描述:LED显示驱动器 RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| MAX6953EAX+ | 功能描述:LED显示驱动器 2.7-5.5V 4-Digit 5x7 Matrix LED Driver RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。