- 您现在的位置：买卖IC网 > PDF目录20223 > MAX6956AAI+ (Maxim Integrated)IC DRIVER LED PORT 20/28 28-SSOP PDF资料下载
参数资料
| 型号： | MAX6956AAI+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 6/24页 |
| 文件大小： | 0K |
| 描述： | IC DRIVER LED PORT 20/28 28-SSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 46 |
| 显示器类型： | LED |
| 接口： | I²C |
| 电流 - 电源： | 180µA |
| 电源电压： | 2.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 28-SSOP |
| 包装： | 管件 |
| 产品目录页面： | 1423 (CN2011-ZH PDF) |
2-Wire-Interfaced, 2.5V to 5.5V, 20-Port or
28-Port LED Display Driver and I/O Expander
Table 1. Port Configuration Map
REGISTER
ADDRESS
CODE (HEX)
D7
D6
D5
REGISTER DATA
D4 D3
D2
D1
D0
Port Configuration for P7, P6, P5, P4
Port Configuration for P11, P10, P9, P8
Port Configuration for P15, P14, P13, P12
Port Configuration for P19, P18, P17, P16
Port Configuration for P23, P22, P21, P20
Port Configuration for P27, P26, P25, P24
Port Configuration for P31, P30, P29, P28
0x09
0x0A
0x0B
0x0C
0x0D
0x0E
0x0F
P7
P11
P15
P19
P23
P27
P31
P6
P10
P14
P18
P22
P26
P30
P5
P9
P13
P17
P21
P25
P29
P4
P8
P12
P16
P20
P24
P28
Table 2. Port Configuration Matrix
PORT
MODE
FUNCTION
PORT
REGISTER
(0x20–0x5F)
PIN BEHAVIOR
ADDRESS
CODE (HEX)
CONFIGURATION
BIT PAIR
UPPER
LOWER
Register bit = 0
High impedance
Output
LED Segment Driver
Register bit = 1
Open-drain current sink, with sink
current (up to 24mA) determined
0x09 to 0x0F
0
0
by the appropriate current register
Output
Input
Input
GPIO Output
GPIO Input
Without Pullup
GPIO Input with Pullup
Register bit = 0
Register bit = 1
Register bit =
input logic level
Active-low logic output
Active-high logic output
Schmitt logic input
Schmitt logic input with pullup
0x09 to 0x0F
0x09 to 0x0F
0x09 to 0x0F
0
1
1
1
0
1
Note: The logic is inverted between the two output modes; a high makes the output go low in LED segment driver mode (0x00) to
turn that segment on; in GPIO output mode (0x01), a high makes the output go high.
simplify access to displays that overlap two MAX6956s,
the MAX6956 provides four virtual ports, P0 through P3.
To update an overlapping digit, send the same code
twice as an eight-port write, once to P28 through P35 of
the first driver, and again to P0 through P7 of the sec-
ond driver. The first driver ignores the last 4 bits and
the second driver ignores the first 4 bits.
Two addressing methods are available. Any single port
(bit) can be written (set/cleared) at once; or, any
sequence of eight ports can be written (set/cleared) in
any combination at once. There are no boundaries; it is
equally acceptable to write P0 through P7, P1 through
P8, or P31 through P38 (P32 through P38 are nonexis-
tent, so the instructions to these bits are ignored).
Using 8-bit control, a seven-segment digit with a deci-
mal point can be updated in a single byte-write, a 14-
segment digit with DP can be updated in two byte-
writes, and 16-segment digits with DP can be updated
in two byte-writes plus a bit write. Also, discrete LEDs
and GPIO port bits can be lit and controlled individually
without affecting other ports.
Shutdown
When the MAX6956 is in shutdown mode, all ports are
forced to inputs (which an be read), and the pullup cur-
rent sources are turned off. Data in the port and control
registers remain unaltered, so port configuration and
output levels are restored when the MAX6956 is taken
out of shutdown. The display driver can still be pro-
grammed while in shutdown mode. For minimum sup-
ply current in shutdown mode, logic inputs should be at
GND or V+ potential. Shutdown mode is exited by set-
ting the S bit in the configuration register (Table 8).
6
_______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| BAS40LT1 | DIODE SCHOTTKY 40V SOT23 |
| R0.5Z-2412/HP-R | CONV DC/DC 0.5W 24VIN 12VOUT |
| IDT71V3557S80BQ8 | IC SRAM 4MBIT 80NS 165FBGA |
| IDT71V3557S80BQ | IC SRAM 4MBIT 80NS 165FBGA |
| IDT71V3557S75PFI8 | IC SRAM 4MBIT 75NS 100TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6956AAI+ | 功能描述:LED显示驱动器 2.5-5.5V 20/28Port LED Display Driver RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| MAX6956AAI+T | 功能描述:LED显示驱动器 2.5-5.5V 20/28Port LED Display Driver RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| MAX6956AAI-T | 功能描述:LED显示驱动器 RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| MAX6956AAX | 功能描述:LED显示驱动器 RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| MAX6956AAX/V+ | 功能描述:LED显示驱动器 2.5-5.5V 20/28Port LED Display Driver RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。