- 您现在的位置：买卖IC网 > PDF目录20166 > MAX6958AAEE+T (Maxim Integrated)IC DRVR DSPL LED 16-QSOP PDF资料下载
参数资料
| 型号： | MAX6958AAEE+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 16/19页 |
| 文件大小： | 0K |
| 描述： | IC DRVR DSPL LED 16-QSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 显示器类型： | LED |
| 配置： | 7 段 + 2 个信号器 |
| 接口： | SMBus（2 线/I²C） |
| 数字或字符： | 4 位数字 |
| 电流 - 电源： | 5.9mA |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-QSOP |
| 包装： | 带卷 (TR) |
2-Wire Interfaced, 3V to 5.5V, 4-Digit,
9-Segment LED Display Drivers with Keyscan
Key Debounced Register (MAX6959 Only)
The key debounced register shows which keys have
been detected as debounced by the keyscanning cir-
cuit (Table 17). Each bit in the register corresponds to
one key switch. The bit is set to 1 if the switch has been
correctly debounced since the last key debounced reg-
ister read operation.
Reading the key debounced register clears the register
(after the data has been read) so that future key presses
can be identified. If the key debounced register is not
read, the keyscan data accumulates. There is no FIFO
register in the MAX6959. Key-press order, or whether a
key has been pressed more than once, cannot be
determined unless the key debounced register is read
after each interrupt and before completion of the next
keyscan cycle.
Reading the key debounced register clears the IRQ
output. If a key is pressed and held down, the key is
reported as debounced (and an IRQ is issued) only
once. The key must be detected as released by the
keyscanning circuit before it is debounced again.
The key debounced register is read only. A write to
address 0x08 is ignored.
Key Pressed Register (MAX6959 Only)
The key pressed register shows which keys have been
detected as pressed by the keyscanning circuit during
the last test. Each bit in the register corresponds to one
key switch. The bit is set if the switch has been detect-
ed as pressed by the keyscanning circuit during the
last test. The bit is cleared if the switch has not been
Table 17. Key Debounced Register Format
detected as pressed by the keyscanning circuit during
the last test. Reading the key pressed register does not
clear either the key pressed register, or the key
debounced register, and does not clear the IRQ output.
The key pressed register is read only. A write to
address 0x0C is ignored.
Display Test Register
The display test register operates in two modes: normal
and display test (Table 19). Display test mode turns on
all LEDs by overriding, but not altering, all control and
digit registers (including the shutdown register) except
for the port configuration register. The duty cycle while
in display test mode is 28/64.
Applications Information
Driving Bicolor LEDs
Bicolor digits combine a red and a green die for each
display element, so that the element displays red or
green (or orange), depending on which die (or both) is
lit. The MAX6958/MAX6959 treat a bicolor digit as two
monocolor digits.
Low-Voltage Operation
The MAX6958/MAX6959 are guaranteed to drive a 23mA
segment current into 2.4V (or lower) LEDs when operat-
ed from a supply voltage of 4.5V to 5.5V. Operating the
MAX6958/MAX6959 from a supply voltage lower than
4.5V reduces the LED drive current. The drivers drive at
least 15.5mA segment current into 2V (or lower) LEDs
when operated from a 3V supply voltage.
KEY DEBOUNCED REGISTER
ADDRESS
CODE (HEX)
REGISTER DATA
WITH APPROPRIATE SWITCH NAMED BELOW
D7
D6
D5
D4
D3
D2
D1
D0
Key debounced register
0x08
Key7
Key6
Key5
Key4
Key3
Key2
Key1
Key0
Table 18. Key Pressed Register Format
KEY PRESSED REGISTER
ADDRESS
CODE (HEX)
REGISTER DATA
WITH APPROPRIATE SWITCH NAMED BELOW
D7
D6
D5
D4
D3
D2
D1
D0
Key pressed register
0x0C
Key7
Key6
Key5
Key4
Key3
Key2
Key1
Key0
Table 19. Display Test Register
MODE
ADDRESS
CODE (HEX)
D7
D6
D5
REGISTER DATA
D4 D3
D2
D1
D0
Normal operation
Display test mode
0x07
0x07
X
X
X
X
X
X
X
X
X
X
X
X
X
X
0
1
16
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| IDT71V424S12PHI8 | IC SRAM 4MBIT 12NS 44TSOP |
| PSA60R-560-R-CNR5 | ADAPTER WALL R-SERIES 60W 56V |
| IDT71V424S12PHI | IC SRAM 4MBIT 12NS 44TSOP |
| TAS225K050P1C-F | CAP TANT 2.2UF 50V 10% AXIAL |
| MAX6931AUI+T | IC SRL-INTF VFD TUBE DVR 28TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6958AAPE | 功能描述:LED显示驱动器 RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| MAX6958AAPE+ | 功能描述:LED显示驱动器 3-5.5V 4-Digit 9-Seg LED Display Driver RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| MAX6958BAEE | 功能描述:LED显示驱动器 3-5.5V 4-Digit 9-Seg LED Display Driver RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| MAX6958BAEE+ | 功能描述:LED显示驱动器 3-5.5V 4-Digit 9-Seg LED Display Driver RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| MAX6958BAEE+T | 功能描述:LED显示驱动器 3-5.5V 4-Digit 9-Seg LED Display Driver RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。