- 您现在的位置：买卖IC网 > PDF目录20741 > MAX6966ATE+T (Maxim Integrated)IC LED DRIVER LINEAR 16-TQFN PDF资料下载
参数资料
| 型号： | MAX6966ATE+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 8/29页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVER LINEAR 16-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 恒定电流： | 是 |
| 拓扑： | 开路漏极，PWM |
| 输出数： | 10 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光 |
| 类型 - 次要： | RGB，白色 LED |
| 频率： | 270kHz ~ 450kHz |
| 电源电压： | 2.25 V ~ 3.6 V |
| 输出电压： | 7V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WFQFN 裸露焊盘 |
| 供应商设备封装： | 16-TQFN（3x3） |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 125°C |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
MAX6966/MAX6967
10-Port Constant-Current LED Drivers and I/O
Expanders with PWM Intensity Control
I/O PORT
8-BIT LATCH
OUTPUT PORT
REGISTER
POSITION A: 0x00 - 0x01
POSITION B: 0x02 - 0xFF
CLOSE SWITCH: 0x02-0xFE
PWM
GENERATOR
ENABLE
A
B
TO/FROM
SERIAL
INTERFACE
1-BIT LATCH
OUTPUT CURRENT
REGISTER
MSB
4-BIT DAC
SET
CURRENT
N
3-BIT LATCH
GLOBAL CURRENT
REGISTER
READ I/O
PORT COMMAND
Figure 1. Simplified Schematic of I/O Ports
Figure 1 shows the I/O port structure of the MAX6966/
MAX6967. I/O ports P0 to P9 default to high impedance
on power-up, so LED or other port loads connected
draw no current, and ports used as inputs do not load
their source signals.
Standby Mode and Operating Current
When all the ports are configured as logic inputs or out-
puts (all output registers set to value 0x00 or 0x01) or
LED off (output register set to value 0xFF), the
MAX6966/MAX6967 operate at their lowest supply cur-
rent, called standby mode.
When PWM intensity control is used (one or more out-
put registers set to a value between 0x03 and 0xFE),
the operating current increases because the internal
PWM circuitry is running.
The operating current also increases whenever a port
that is set is active low as a constant-current output
(output register set to a value between 0x02 and 0xFE),
even if a load is not applied to the port. This current
increase is due to an internal current mirror being
enabled for that port output to provide the accurate
constant-current sink. There is a gated mirror for each
output, and each mirror is only enabled when required.
When PWM is used, a current mirror is only turned on
for the output’s on-time. This means that operating cur-
rent varies as constant-current outputs are turned on
8
and off through the serial interface, as well as by the
PWM intensity control.
Shutdown Mode
In shutdown mode, all ports configured as constant-cur-
rent outputs (output register set to a value between 0x02
and 0xFE) are switched off, and these outputs go high
impedance as if their registers were set to value 0xFF.
Ports configured as logic inputs or outputs (output regis-
ters set to value 0x00 or 0x01) are unaffected ( Table 1).
This means that any ports used for GPIOs are still fully
operational in shutdown mode, and port inputs can be
read and output ports can be toggled at any time using
the serial interface. The MAX6966/MAX6967 can there-
fore be used for a mix of logic inputs, logic outputs, and
PWM LED drivers, and only the LED drivers are turned
off automatically in shutdown.
The MAX6966/MAX6967 are put into shutdown mode
by clearing the run bit (bit D0) in the configuration reg-
ister ( Table 4). Shutdown is exited by setting the run bit
through the serial interface, or by using the CS run
option discussed below. The MAX6966/MAX6967 can
be configured and controlled in the normal way through
the serial interface in shutdown mode. All registers are
accessible in shutdown mode, and no register is
changed by shutdown mode. When shutdown mode is
exited, ports configured as constant-current outputs at
that time start instantly with their current PWM values.
Maxim Integrated
相关PDF资料 |
PDF描述 |
|---|---|
| NCV86602DT50RKG | IC REG LDO 5V .15A DPAK-5 |
| HMM43DSUH | CONN EDGECARD 86POS .156 DIP SLD |
| MRA4003T3G | DIODE STD REC 1A 300V SMA |
| NCV8518APWR2G | IC REG LDO 5V .25A 16-SOIC |
| EYM10DRSS | CONN EDGECARD 20POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6966EVCMAXQU | 功能描述:LED 照明开发工具 MAXIM EVALUATION SYSTEM RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
| MAX6966EVKIT | 功能描述:LED 照明开发工具 Evaluation Kit/Evaluation System for the MAX6966 RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
| MAX6967AEE | 功能描述:LED显示驱动器 10-Port Constant Current LED Driver RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| MAX6967AEE+ | 功能描述:LED显示驱动器 10-Port Constant Current LED Driver RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| MAX6967AEE+T | 功能描述:LED显示驱动器 10-Port Constant Current LED Driver RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。