- 您现在的位置：买卖IC网 > Datasheet目录341 > MAX6967ATE+ (Maxim Integrated)IC LED DRIVER LINEAR 16-TQFN Datasheet资料下载
参数资料
| 型号： | MAX6967ATE+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 14/29页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVER LINEAR 16-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 100 |
| 恒定电流： | 是 |
| 拓扑： | 开路漏极，PWM |
| 输出数： | 10 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光 |
| 类型 - 次要： | RGB，白色 LED |
| 频率： | 270kHz ~ 450kHz |
| 电源电压： | 2.25 V ~ 3.6 V |
| 输出电压： | 7V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WFQFN 裸露焊盘 |
| 供应商设备封装： | 16-TQFN（3x3） |
| 包装： | 管件 |
| 工作温度： | -40°C ~ 125°C |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
MAX6966/MAX6967
10-Port Constant-Current LED Drivers and I/O
Expanders with PWM Intensity Control
The stagger bit is ideally set or cleared when the
MAX6966/MAX6967 are in shutdown. If not, there may be
a perceived transient flicker in any PWM-controlled LEDs
because the fundamental PWM timing is being changed.
Configuration Register
The configuration register is used to select PWM phas-
ing between outputs, test fade status, enable hardware
startup from shutdown, and select shutdown or run
mode ( Table 4).
GPIO Port Direction Configuration
The 10 I/O ports P0 through P9 can be configured to
any combination of logic inputs, logic outputs, and con-
stant-current outputs. Configure any port as a logic
input by setting its output register to 0x01, which sets
the port output high impedance ( Table 6).
Input Ports Registers
Reading an input port register returns the logic levels at
the I/O port pins for ports that have been configured as a
logic input ( Table 5). A port is configured as a logic input
by writing 0x01 to the port’s output register ( Table 5). An
input ports register returns logic 0 in the appropriate bit
position for a port not configured as a logic input.
The input ports registers are read only. A write to an
input ports register is ignored.
Table 5. Input Ports Register
ADDRESS
Output Registers and
PWM Intensity Control
The MAX6966/MAX6967 use one 8-bit register to control
each output port ( Table 6). Each port may be configured
as a logic input, open-drain logic output, or constant-cur-
rent sink with programmable current and PWM duty
cycle. Ports withstand 7V independent of the MAX6966’s
or MAX6967’s supply voltage, whether used as logic
inputs, logic outputs, or constant-current sinks.
Ports configured as constant-current outputs sink a con-
stant current set by the output current registers ( Table 7)
and the global current registers ( Table 8). This current
may be PWM with a duty cycle ranging from 3/256 to
254/256 to reduce the average current, or remain static.
The 10 registers 0x00 through 0x09 control an I/O port
each ( Table 6). Five pseudo-register addresses, 0x0B
through 0x0F, allow groups of outputs to be set to the
same value with a single command by writing the same
data to multiple output registers.
PWM timing for LED intensity control is generated using
either the internal 32kHz oscillator, or an external clock
on DOUT/OSC. The PWM clock source is selected by
configuration register bit D7 ( Table 4). The MAX6966
powers up configured to use the internal 32kHz oscilla-
tor by default. The MAX6967 powers up configured to
use the external clock source by default.
REGISTER DATA
REGISTER
R/W
CODE
(HEX)
D7
D6
D5
D4
D3
D2
D1
D0
Read input ports P7–P0
Read input ports P9–P8
1
1
0x0E
0x0F
Port P7
0
Port P6
0
Port P5
0
Port P4
0
Port P3
0
Port P2
0
Port P1
Port P9
Port P0
Port P8
14
Maxim Integrated
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6968AAE+ | IC LED DRIVER LINEAR 16-SSOP |
| MAX6970AUE+ | IC LED DRIVER LINEAR 16-TSSOP |
| MAX6971AUG+T | IC LED DRIVER LINEAR 24-TSSOP |
| MAX6974ATL+ | IC LED DRIVER LINEAR 40-TQFN |
| MAX6977AAE+ | IC LED DRIVER LINEAR 16-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6967ATE+ | 功能描述:LED显示驱动器 10-Port Constant Current LED Driver RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| MAX6967ATE+T | 功能描述:LED显示驱动器 10-Port Constant Current LED Driver RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| MAX6967ATE-T | 功能描述:LED显示驱动器 10-Port Constant Current LED Driver RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| MAX6968AAE | 功能描述:LED显示驱动器 8-Port 5.5V Constant Current LED Driver RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| MAX6968AAE+ | 功能描述:LED显示驱动器 8-Port 5.5V Constant Current LED Driver RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。