参数资料
型号: MAX6969AUG+T
厂商: Maxim Integrated
文件页数: 9/12页
文件大小: 0K
描述: IC LED DRIVER LINEAR 24-TSSOP
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 2,500
恒定电流:
拓扑: 线性,高端
输出数: 16
内部驱动器:
类型 - 主要: LED 照明显示器,标牌,汽车
电源电压: 3 V ~ 5.5 V
输出电压: 5.5V
安装类型: 表面贴装
封装/外壳: 24-TSSOP(0.173",4.40mm 宽)
供应商设备封装: 24-TSSOP
包装: 带卷 (TR)
工作温度: -40°C ~ 125°C
16-Port, 5.5V Constant-Current LED Driver
Applications Information
Selecting External Component R SET to Set
LED Output Current
The MAX6969 uses an external resistor, R SET , to set the
LED current for outputs OUT0–OUT15. The minimum
allowed value of R SET is 327.3 ? , which sets the output
currents to 55mA. The maximum allowed value of R SET
is 1.5k ? . The reference value, 360 ? , sets the output
currents to 50mA. To set a different output current, use
Overtemperature Cutoff
The MAX6969 contains an internal temperature sensor
that turns off all outputs when the die temperature
exceeds approximately +165°C. The outputs are
enabled again when the die temperature drops below
approximately +140°C. Register contents are not
affected, so when a driver is overdissipating, the exter-
nal symptom is the load LEDs cycling between on and
off as the driver repeatedly overheats and cools, alter-
nately turning the LEDs off and then back on again.
the formula:
R SET = 18,000 / I OUT
Power-Supply Considerations
The MAX6969 operates with a chip supply V+, and one
where I OUT is the desired output current in mA.
Computing Power Dissipation
The upper limit for power dissipation (P D ) for the
MAX6969 is determined by the following equation:
P D = (V+ x I+) + (V OUT x DUTY x I OUT x N)
where:
V+ = supply voltage
I+ = operating supply current when sinking I OUT LED
drive current into N outputs
DUTY = PWM duty cycle applied to OE
N = number of MAX6969 outputs driving LEDs at the
same time (maximum is 16)
V OUT = MAX6969 port output voltage when driving load
LED(s)
I OUT = LED drive current programmed by R SET
P D = power dissipation, in mW if currents are in mA
Dissipation example:
I OUT = 47mA, N = 16, DUTY = 1, V OUT = 2V, V+ =
5.25V
P D = (5.25V x 50mA) + (2V x 1 x 47mA x 16) = 1.767W
Thus, for a 24-pin TSSOP package (T JA = 1 / 0.0122 =
+82°C/W from the Absolute Maximum Ratings ), the
maximum allowed ambient temperature T A is given by:
T J(MAX) = T A + (P D x T JA ) = +150°C =
T A + (1.767 x 82°C/W)
so T A = +145.6°C.
or more LED supplies. Bypass each supply to GND
with a 0.1μF capacitor as close to the MAX6969 as pos-
sible. This is normally adequate for static LED driving.
For multiplex or PWM applications, it is necessary to
add an additional bulk electrolytic capacitor of 4.7μF or
more to each supply for every 4 to 16 MAX6969s. The
necessary capacitance depends on the LED load cur-
rent, PWM switching frequency, and serial-interface
speed. Inadequate V+ decoupling can cause timing
problems, and very noisy LED supplies can affect LED
current regulation.
_______________________________________________________________________________________
9
相关PDF资料
PDF描述
TPSE687K004R0040 CAP TANT 680UF 4V 10% 2917
EMC43DRYS-S93 CONN EDGECARD 86POS DIP .100 SLD
GEC10DREH-S93 CONN EDGECARD 20POS .100 EYELET
VI-J3W-CX-F2 CONVERTER MOD DC/DC 5.5V 75W
GEC08DRYS-S734 CONN EDGECARD 16POS DIP .100 SLD
相关代理商/技术参数
参数描述
MAX6969AWG 功能描述:LED显示驱动器 16-Port 5.5V Const Current LED Driver RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube
MAX6969AWG+ 功能描述:LED显示驱动器 16-Port 5.5V Const Current LED Driver RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube
MAX6969AWG+T 功能描述:LED显示驱动器 16-Port 5.5V Const Current LED Driver RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube
MAX6969AWG-G05 功能描述:LED显示驱动器 16-Port 5.5V Const Current LED Driver RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube
MAX6969AWG-T 功能描述:LED显示驱动器 16-Port 5.5V Const Current LED Driver RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube