- 您现在的位置：买卖IC网 > PDF目录18710 > MAX7042EVKIT-315+ (Maxim Integrated)EVAL KIT MAX7042 PDF资料下载
参数资料
| 型号： | MAX7042EVKIT-315+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 10/17页 |
| 文件大小： | 0K |
| 描述： | EVAL KIT MAX7042 |
| 标准包装： | 1 |
| 系列： | * |
308MHz/315MHz/418MHz/433.92MHz
Low-Power, FSK Superheterodyne Receiver
Detailed Description
The MAX7042 CMOS superheterodyne receiver and a
few external components provide a complete FSK
receive chain from the antenna to the digital output
data. FSK uses the difference in frequency of the carri-
er to represent a logic 0 and logic 1. Depending on sig-
nal power and component selection, data rates as high
as 66kbps NRZ can be achieved.
Frequency Selection
impedance such as printed circuit board (PCB) trace
antenna. A nominal value of this inductor for a 50 ? input
impedance is 3.9nH at 315MHz and 0nH (short) at
433.92MHz, but is affected by the PCB trace. See the
Typical Operating Characteristics for the relationship
between the inductance and input impedance.
The LC tank filter connected to LNAOUT consists of L2
and C9 (see the Typical Application Circuit). Select L2
and C9 to resonate at the desired RF input frequency.
The resonant frequency is given by:
The MAX7042 can be tuned to one of four frequencies
using the 2 frequency-select bits FSEL1 and FSEL2:
308, 315, 418, and 433.92MHz, as shown in Table 1.
The LO frequencies are 32 times the crystal reference
f =
1
2 π L TOTAL x C TOTAL
frequencies of 9.29063, 9.50939, 12.72813, and
13.22563MHz. The selected crystal frequency is used
to calibrate the FSK detector PLL so that it operates at
the middle of the 10.7MHz IF.
Table 1. Frequency Selection Table
where L TOTAL = L2 + L PARASITICS and C TOTAL = C9 +
C PARASITICS .
L PARASITICS and C PARASITICS include inductance and
capacitance of the PCB traces, package pins, mixer
input impedance, LNA output impedance, etc. These
parasitics at high frequencies cannot be ignored, and
FSEL2
0
0
1
1
FSEL1
0
1
0
1
FREQUENCY
(MHz)
308
315
418
433.92
can have a dramatic effect on the tank filter center fre-
quency. Lab experimentation is required to optimize the
center frequency of the tank. The parasitic capacitance
is generally 5pF to 7pF.
There are two ways to verify experimentally that the res-
onant frequency of the tank is centered at the desired
RF frequency:
Low-Noise Amplifier (LNA)
The LNA is a cascode amplifier with off-chip inductive
degeneration. The gain and the noise figure are depen-
dent on both the antenna matching network at the LNA
input and the LC tank network between the LNA output
and the mixer input.
The MAX7042 allows for user programmability of the
LNA bias current. Input LNASEL programs 1x to 2x
bias currents in increments of 0.6mA from 0.6mA to
1.2mA. Setting LNASEL to logic-low programs the LNA
to consume 1x bias current and setting LNASEL to
logic-high programs the LNA to consume 2x bias cur-
rent. Larger bias currents yield better sensitivity and
gain at the expense of current drain.
The off-chip inductive degeneration is achieved by
connecting an inductor from LNASRC to AGND. This
inductor sets the real part of the input impedance at
LNAIN, allowing for a more flexible match to a low-input
1) Drive the crystal oscillator externally and sweep both
the RF frequency and the LO frequency (FXTAL x
32) to keep the IF at 10.7MHz while monitoring the
RSSI voltage (pin 4). There is a peak in the RSSI
voltage at resonance. The external source must be
AC-coupled into XTAL1 and the XTAL2 pin must
have an AC bypass to ground. The recommended
drive power is -10dBm.
2) Use a network analyzer to measure the resonance.
The port 1 power from the network analyzer is input
to the receiver, and this power must be -30dBm or
less. A coaxial stub with the center conductor
exposed (commonly called an RF “sniffer” is used to
monitor the tank power and serves as the port 2
input to the network analyzer. The sniffer should be
placed in close proximity to, but not actually touch-
ing, the tank inductor.
10
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX7032EVKIT-433 | EVAL KIT MAX7032 |
| MAX7036EVKIT-315+ | EVAL KIT MAX7036 |
| MAX7034EVKIT-315+ | EVAL KIT MAX7034 |
| MAX1472EVKIT-315 | EVAL KIT MAX1472 |
| 0622022020 | TOOL INSERTION 50POS 4ROWS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX7042EVKIT-315+ | 功能描述:射频开发工具 MAX7042 Eval Kit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| MAX7042EVKIT-433 | 功能描述:射频开发工具 RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| MAX7042EVKIT-433+ | 功能描述:射频开发工具 MAX7042 Eval Kit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| MAX7043EUI+ | 功能描述:射频收发器 300MHz To 450MHz ASK FSK Superhtrdyne Rec RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray |
| MAX7043EUI+T | 功能描述:射频收发器 300MHz To 450MHz ASK FSK Superhtrdyne Rec RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。