参数资料
型号: MAX7044EVKIT-315
厂商: Maxim Integrated
文件页数: 7/10页
文件大小: 0K
描述: EVAL KIT MAX7044
标准包装: 1
系列: *
300MHz to 450MHz High-Efficiency,
Crystal-Based +13dBm ASK Transmitter
t WAIT =
frequency.  For  other  frequencies,  calculate  the  wait
time with the following equation:
2 16 x 32
f RF
where t WAIT is the wait time to shutdown and f RF is the
RF transmit frequency.
When the device is in shutdown, a rising edge on DATA
initiates the warm up of the crystal and PLL. The crystal
and PLL must have 220μs settling time before data can
be transmitted. The 220μs turn-on time of the MAX7044
is dominated by the crystal oscillator startup time. Once
the oscillator is running, the 1.6MHz PLL loop band-
width allows fast frequency recovery during power
amplifier toggling.
When the device is operating, each edge on the data
line resets an internal counter to zero and it begins to
count again. If no edges are detected on the data line,
the counter reaches the end-of-count (2 16 clock cycles)
and places the device in shutdown mode. If there is an
edge on the data line before the counter hits the end of
count, the counter is reset and the process starts over.
It may be necessary to keep the power amplifier on
steadily for testing and debugging purposes. To do
this, set the DATA pin voltage slightly above the mid-
point between V DD and ground (V DD /2 + 100mV).
Phase-Locked Loop
The PLL block contains a phase detector, charge
pump, integrated loop filter, VCO, asynchronous 32x
clock divider, and crystal oscillator. This PLL requires
no external components. The relationship between the
carrier and crystal frequency is given by:
f XTAL = f RF /32
The lock-detect circuit prevents the power amplifier
from transmitting until the PLL is locked. In addition, the
device shuts down the power amplifier if the reference
frequency is lost.
The Typical Application Circuit delivers +13dBm at
+2.7V supply with 7.7mA of supply current. Thus, the
overall efficiency is 48% with the efficiency of the power
amplifier itself greater than 54%.
Buffered Clock Output
The MAX7044 provides a buffered clock output
(CLKOUT) for easy interface to a microcontroller or fre-
quency-hopping generator. The frequency of CLKOUT is
1/16 the crystal frequency. For a 315MHz RF transmit fre-
quency, a crystal of 9.84375MHz is used, giving a clock
output of 615.2kHz. For a 433.92MHz RF frequency, a
crystal of 13.56MHz is used for a clock output of
847.5kHz.
The clock output is inactive when the device is in shut-
down mode. The device is placed in shutdown mode by
the internal data activity detector (see the Shutdown
Mode section). Once data is detected on the data input,
the clock output is stable after approximately 220μs.
Applications Information
Output Power Adjustment
It is possible to adjust the output power down to -15dBm
with the addition of a resistor (see R PWRADJ in Figure 1).
The addition of the power adjust resistor also reduces
power consumption. See the Supply Current and
Output Power vs. External Resistor and Supply Current
vs. Output Power graphs in the Typical Operating
Characteristics section. It is imperative to add both a
low-frequency and a high-frequency decoupling
capacitor as shown in Figure 1.
Crystal Oscillator
The crystal oscillator in the MAX7044 is designed to
present a capacitance of approximately 3pF between
the XTAL1 and XTAL2 pins. If a crystal designed to
3.0V
Power Amplifier (PA)
The PA of the MAX7044 is a high-efficiency, open-
100nF
R PWRADJ
1
XTAL1
f XTAL
XTAL2
8
3.0V
drain, switch-mode amplifier. With a proper output
matching network, the PA can drive a wide range of
impedances, including the small-loop PCB trace anten-
na and any 50 Ω antenna. The output-matching network
for an antenna with a characteristic impedance of 50 Ω
is shown in the Typical Application Circuit. The output-
matching network suppresses the carrier harmonics
and transforms the antenna impedance to an optimal
impedance at PAOUT, which is about 125 Ω .
220pF
ANTENNA
680pF
2
3
4
GND V DD
MAX7044
PAGND DATA
PAOUT CLKOUT
7
6
5
100nF
DATA INPUT
CLOCK
OUTPUT
(f CLKOUT =
f XTAL /16)
When the output matching network is properly tuned,
the power amplifier transmits power with high efficiency.
Figure 1. Output Power Adjustment Circuit
_______________________________________________________________________________________
7
相关PDF资料
PDF描述
0622022040 TOOL INSERTION 50POS 5ROWS
MAX2686LEVKIT# EVAL KIT
MAX2674EVKIT+ EVAL KIT MAX2674
MAX2692EVKIT# EVAL KIT MAX2692
MAX2687EVKIT+ EVAL KIT MAX2687
相关代理商/技术参数
参数描述
MAX7044EVKIT-433 功能描述:射频开发工具 MAX7044 Eval Kit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V
MAX7048ATL+ 制造商:Maxim Integrated Products 功能描述:288-945 MHZ TRANSCEIVER - Rail/Tube
MAX7048ATL+T 制造商:Maxim Integrated Products 功能描述:288-945 MHZ TRANSCEIVER - Tape and Reel
MAX7048EVKIT+ 制造商:Maxim Integrated Products 功能描述:288-945 MHZ TRANSCEIVER EV KIT - Boxed Product (Development Kits)
MAX7049 制造商:未知厂家 制造商全称:未知厂家 功能描述:高性能、288MHz至945MHz ASK/FSK ISM发送器