- 您现在的位置：买卖IC网 > PDF目录18800 > MAX7058ATG+T (Maxim Integrated)IC TX 315MHZ/390MHZ ASK 24-TQFN PDF资料下载
参数资料
| 型号： | MAX7058ATG+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 8/14页 |
| 文件大小： | 0K |
| 描述： | IC TX 315MHZ/390MHZ ASK 24-TQFN |
| 其它有关文件： | Automotive Product Guide |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 频率： | 315MHz ~ 390MHz |
| 应用： | 汽车 RKE，遥控，无线传感器 |
| 调制或协议： | ASK，OOK |
| 数据传输率 - 最大： | 50 kbps |
| 功率 - 输出： | 10dBm |
| 电流 - 传输： | 12.9mA |
| 数据接口： | PCB，表面贴装 |
| 天线连接器： | PCB，表面贴装 |
| 电源电压： | 2.1 V ~ 3.6 V |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 24-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
315MHz/390MHz Dual-Frequency
ASK Transmitter
Detailed Description
The MAX7058 alternately transmits OOK/ASK data at
315MHz or 390MHz using a single crystal. The device
has integrated tuning capacitors at the output of the
power amplifier to ensure high efficiency at each fre-
quency.
The crystal-based architecture of the MAX7058 elimi-
nates many of the common problems with surface
acoustic wave (SAW) transmitters, by providing greater
modulation depth, faster frequency settling, tighter
transmit frequency tolerance, and reduced temperature
dependence. In particular, the tighter transmit frequen-
cy tolerance means that a super-heterodyne receiver
with a narrower IF bandwidth (therefore lower noise
bandwidth) can be used. The payoff is improved over-
all receiver performance when using a super-hetero-
dyne receiver such as the MAX1471, MAX1473,
MAX7033, MAX7034, or MAX7042.
Dual Frequency
The MAX7058 is a crystal-referenced PLL VHF/UHF
transmitter that transmits OOK/ASK data at 315MHz or
390MHz. Two fixed synthesizer-divide ratios of 21 and
26 can be selected, and a 15MHz crystal is used as the
reference for 315MHz/390MHz operation. The FSEL pin
is used to select the divide ratio. The MAX7058 can
operate over a 300MHz to 450MHz range by using dif-
ferent crystal frequencies. The two operating frequen-
cies are always related by a 26:21 ratio.
An internal variable shunt capacitor is connected at the
PA output. This capacitor is controlled by four external
logic bits (CAP1 –CAP4) to maintain highly efficient
transmission at either 315MHz or 390MHz. This means
that it is possible to change the frequency and retune
the antenna to the new frequency in a very short time.
The combination of rapid-antenna tuning ability with
rapid-synthesizer tuning makes the MAX7058 a true fre-
quency-agile transmitter. The tuning capacitor has a
resolution of 0.5pF. When the MAX7058 operates at
315MHz, the capacitance added at PAOUT corre-
sponds to the setting at CAP1–CAP4, as seen in Table
2. When the MAX7058 operates at 390MHz, the
MAX7058 does not add any internal shunt capacitance
at PAOUT.
The MAX7058 supports ASK data rates up to 100kbps
NRZ and features adjustable output power through an
external resistor to more than +10dBm into a 50 Ω load.
Power-Up and Standby Modes
The MAX7058 can be placed in either an enabled state
(all circuit blocks necessary for transmission powered
up) or a disabled state (low-current standby). The state
selection can be controlled either by ENABLE (ENABLE
method) or by activity on DIN (auto-power-up method).
In either method, the MAX7058 can begin transmission
within 250μs after being enabled. Either method can be
used with any TOGGLE/FSEL operating mode.
In the ENABLE method, setting ENABLE to a logic-high
state enables the MAX7058 and setting it to a logic-low
state disables the MAX7058. To avoid conflict with the
auto-power-up method, DIN must be set to a logic-low
state before ENABLE is set to a logic-low state, and
remains low until after ENABLE is set to a logic-
high state.
In the auto-power-up method, ENABLE can be hard-
wired to a logic-low state and a rising edge on DIN
will enable the MAX7058. The MAX7058 will remain
enabled until DIN is placed in a steady logic-low
state for 2 22 cycles of the reference clock (279.62ms
with a 15MHz crystal), at which time the MAX7058 will
be disabled.
When the MAX7058 is enabled, the active pulldowns at
CAP1–CAP4, FSEL, and TOGGLE will be turned on.
When the MAX7058 is disabled, these active pulldowns
will be turned off. The active pulldowns at ENABLE and
DIN are always turned on.
8
_______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| RA203020XX | RECTIFIER 3000V 2000A |
| RA202825XX | RECTIFIER 2800V 2500A |
| ASFLM1-100.000MHZ-L-C | OSC MEMS 100.000 MHZ 3.0V SMD |
| 2N7002W-7-F | MOSFET N-CH 60V 115MA SOT323 |
| LP-40-600 | XFRMR PWR 115/230V 20VAC 1.2A |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX7058EVKIT+ | 功能描述:射频开发工具 MAX7058 Eval Kit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| MAX705C/D | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX705CPA | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX705CPA+ | 功能描述:监控电路 Single uPower Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX705CSA | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。