- 您现在的位置：买卖IC网 > PDF目录18800 > MAX7060ATG+ (Maxim Integrated)IC TX ASK/FSK 280-450MHZ 24TQFN PDF资料下载
参数资料
| 型号： | MAX7060ATG+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 15/31页 |
| 文件大小： | 0K |
| 描述： | IC TX ASK/FSK 280-450MHZ 24TQFN |
| 标准包装： | 75 |
| 频率： | 280MHz ~ 450MHz |
| 应用： | 通用 |
| 调制或协议： | ASK，OOK |
| 数据传输率 - 最大： | 140kbps |
| 功率 - 输出： | 15dBm |
| 电流 - 传输： | 34mA |
| 数据接口： | PCB，表面贴装 |
| 天线连接器： | PCB，表面贴装 |
| 电源电压： | 2.1 V ~ 3.6 V，4.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 24-WFQFN 裸露焊盘 |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
MAX7060
280MHz to 450MHz Programmable
ASK/FSK Transmitter
C M ? 1 1 ? 6
Crystal (XTAL) Oscillator
The XTAL oscillator in the MAX7060 is designed to pres-
ent a capacitance of approximately 6pF between the
XTAL1 and XTAL2 pins. In most cases, this corresponds
to a 8pF load capacitance applied to the external crystal
when typical PCB parasitics are added. It is very impor-
tant to use a crystal with a load capacitance equal to the
capacitance of the MAX7060 crystal oscillator plus PCB
parasitics. If a crystal designed to oscillate with a differ-
ent load capacitance is used, the crystal is pulled away
from its stated operating frequency, introducing an error
in the reference frequency. A crystal designed to oper-
ate at a higher load capacitance than the value specified
for the oscillator is always pulled higher in frequency.
Adding capacitance to increase the load capacitance
on the crystal increases the startup time and can prevent
oscillation altogether.
In actuality, the oscillator pulls every crystal. The crystal’s
natural frequency is really below its specified frequency,
but when loaded with the specified load capacitance,
the crystal is pulled and oscillates at its specified fre-
quency. This pulling is already accounted for in the
specification of the load capacitance.
Additional pulling can be calculated if the electrical
parameters of the crystal are known. The frequency pull-
ing is given by:
f P
= ? ? ? × 10
2 ? C CASE + C LOAD C CASE + C SPEC ?
General-Purpose Output
(GPO)/Clock Outputs
The MAX7060 has two GPO pins in SPI mode (GPO2_
MOD and GPO1) and one GPO in manual mode (GPO1).
The GPO1 pin can serve as a clock for a microprocessor
or any other GPO function in SPI mode. In manual mode,
this pin outputs the synthesizer lock-detect (lockdet)
status, after which the user can send data through the
DIN pin.
The GPO2_MOD pin acts as the SPI data output when
the CS _DEV pin is low, in SPI mode. When CS _DEV is
high, it acts as a GPO that can output various internal
signals, such as the synthesizer lock detect (lockdet).
In SPI mode, the output clock that can be routed through
GPO1 is a divided version of the crystal frequency. The
divide ratio is set through the MAX7060 registers, and
the divide settings are 1 (no division), 2, 4, 8, or 16.
When driving an output clock through GPO1, the gp1bst
bit (register Conf0, address 0x01, bit 6) can be set to
1 to increase GPO1 drive strength. If even more drive
capability is required, the user should provide an exter-
nal buffer.
Serial Peripheral Interface (SPI)
The MAX7060 utilizes a 4-wire SPI protocol for pro-
gramming its registers, configuring and controlling the
operation of the whole transmitter. For SPI operation, the
FREQ2, FREQ1, and FREQ0 pins must be reset to 0.
The following digital I/Os control the operation of the SPI:
where:
f P is the amount the crystal frequency pulled in ppm
C M is the motional capacitance of the crystal
C CASE is the case capacitance
CS _DEV
SDI_PWR1
SCLK_PWR0
GPO2_MOD
Active-low SPI chip select
SPI data Input
SPI clock
SPI data output
C SPEC is the specified load capacitance
C LOAD is the actual load capacitance
When the crystal is loaded as specified (i.e., C LOAD =
C SPEC ), the frequency pulling equals zero.
Maxim Integrated
Figure 2 shows the general timing diagram of the SPI
protocol.
Any number of 8-bit data bursts (Data 1, Data 2 … Data
n) can be sent within one cycle of the CS _DEV pin, to
allow for burst-write or burst-read operations. The SPI
data output signal is routed through the GPO2_MOD pin
when CS _DEV is low.
15
相关PDF资料 |
PDF描述 |
|---|---|
| FK2125T406AL-T | FILTER EMI 40MHZ 100MA 0805 |
| DP-241-7-36 | XFRMR PWR 115/230V 36VCT 1.5A |
| MAX2370ETM+ | IC TRANSMITTER QUAD 48TQFN-EP |
| 241-7-16 | XFRMR PWR 115V 16VCT 3.5A |
| MAX2904ETI+ | IC TX 868MHZ 200MW 28TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX7060ATG/V | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:280MHz to 450MHz Programmable ASK/FSK Transmitter |
| MAX7060ATG/V+ | 功能描述:射频发射器 300-450 MHz ASK/FSK Transmitter RoHS:否 制造商:Micrel 类型:ASK Transmitter 封装 / 箱体:SOT-23-6 工作频率:300 MHz to 450 MHz 封装:Reel |
| MAX7060ATG/V+T | 功能描述:射频发射器 300-450 MHz ASK/FSK Transmitter RoHS:否 制造商:Micrel 类型:ASK Transmitter 封装 / 箱体:SOT-23-6 工作频率:300 MHz to 450 MHz 封装:Reel |
| MAX7060ATG+ | 功能描述:射频发射器 280-450MHz Prog ASK/FSK Transmitter RoHS:否 制造商:Micrel 类型:ASK Transmitter 封装 / 箱体:SOT-23-6 工作频率:300 MHz to 450 MHz 封装:Reel |
| MAX7060ATG+T | 功能描述:射频发射器 280-450MHz Prog ASK/FSK Transmitter RoHS:否 制造商:Micrel 类型:ASK Transmitter 封装 / 箱体:SOT-23-6 工作频率:300 MHz to 450 MHz 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。