- 您现在的位置：买卖IC网 > PDF目录16238 > MAX713CSE+ (Maxim Integrated Products)IC BATT FASTCHRG NICD/NIMH16SOIC PDF资料下载
参数资料
| 型号： | MAX713CSE+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 5/17页 |
| 文件大小： | 0K |
| 描述： | IC BATT FASTCHRG NICD/NIMH16SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 功能： | 充电管理 |
| 电池化学： | 镍镉（NiCd）、镍金属氢化物（NiMH） |
| 电源电压： | 4.5 V ~ 5.5 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SOIC |
| 包装： | 管件 |
| 产品目录页面： | 1409 (CN2011-ZH PDF) |
MAX712/MAX713
NiCd/NiMH Battery
Fast-Charge Controllers
Pin Description
PIN
1
2
3, 4
5
6
7
8
9, 10
11
12
13
14
15
16
NAME
VLIMIT
BATT+
PGM0,
PGM1
THI
TLO
TEMP
FASTCHG
PGM2,
PGM3
CC
BATT-
GND
DRV
V+
REF
FUNCTION
Sets the maximum cell voltage. The battery terminal voltage (BATT+ - BATT-) will not exceed VLIMIT x
(number of cells). Do not allow VLIMIT to exceed 2.5V. Connect VLIMIT to VREF for normal operation.
Alternatively, connect VLIMIT to V+ to set the maximum cell voltage to an internally preset 1.65V/cell.
Positive terminal of battery
PGM0 and PGM1 set the number of series cells to be charged. The number of cells can be set from
1 to 16 by connecting PGM0 and PGM1 to any of V+, REF, or BATT-, or by leaving the pin unconnected
(Table 2). For cell counts greater than 11, see the Linear-Mode, High Series Cell Count section.
Charging more or fewer cells than the number programmed may inhibit Δ V fast-charge termination.
Trip point for the over-temperature comparator. If the voltage-on TEMP rises above THI, fast charge ends.
Trip point for the under-temperature comparator. If the MAX712/MAX713 power on with the voltage-
on TEMP less than TLO, fast charge is inhibited and will not start until TEMP rises above TLO.
Sense input for temperature-dependent voltage from thermistors.
Open-drain, fast-charge status output. While the MAX712/MAX713 fast charge the battery, FASTCHG
sinks current. When charge ends and trickle charge begins, FASTCHG stops sinking current.
PGM2 and PGM3 set the maximum time allowed for fast charging. Timeouts from 33 minutes to 264
minutes can be set by connecting to any of V+, REF, or BATT-, or by leaving the pin unconnected
(Table 3). PGM3 also sets the fast-charge to trickle-charge current ratio (Table 5).
Compensation input for constant current regulation loop
Negative terminal of battery
System ground. The resistor placed between BATT- and GND monitors the current into the battery.
Current sink for driving the external PNP current source
Shunt regulator. The voltage on V+ is regulated to +5V with respect to BATT-, and the shunt current
powers the MAX712/MAX713.
2V reference output
Maxim Integrated
5
相关PDF资料 |
PDF描述 |
|---|---|
| EMA10DRSD-S288 | CONN EDGECARD 20POS .125 EXTEND |
| 4590R-333K | INDUCTOR HIGH CURRENT 33.0UH |
| RP12-123.3SA | CONV DC/DC 12W 9-18VIN 3.3VOUT |
| RP12-1215SA | CONV DC/DC 12W 9-18VIN 15VOUT |
| MAX712CPE+ | IC BATT FASTCHRG NICD/NIMH 16DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX713CSE+ | 功能描述:电池管理 NiCd/NiMH Battery Fast-Charge Ctlr RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX713CSE+T | 功能描述:电池管理 NiCd/NiMH Battery Fast-Charge Ctlr RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX713CSE-T | 功能描述:电池管理 NiCd/NiMH Battery Fast-Charge Ctlr RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX713EPE | 功能描述:电池管理 NiCd/NiMH Battery Fast-Charge Ctlr RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX713EPE+ | 功能描述:电池管理 NiCd/NiMH Battery Fast-Charge Ctlr RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。