- 您现在的位置：买卖IC网 > PDF目录20781 > MAX7302AEE+ (Maxim Integrated)IC LED DRIVER LINEAR 16-QSOP PDF资料下载
参数资料
| 型号： | MAX7302AEE+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 10/30页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVER LINEAR 16-QSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 100 |
| 拓扑： | 开路漏极，PWM |
| 输出数： | 9 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光，LED 闪烁器 |
| 类型 - 次要： | 白色 LED |
| 频率： | 1MHz |
| 电源电压： | 1.62 V ~ 3.6 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-QSOP |
| 包装： | 管件 |
| 工作温度： | -40°C ~ 125°C |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
SMBus/I 2 C Interfaced 9-Port,
Level-Translating GPIO and LED Driver with CLA
Slave Address
The MAX7302 is set to one of four I 2 C slave addresses,
using the address input AD0 (see Table 5) and is
accessed over an I 2 C or SMBus serial interface up to
400kHz. The MAX7302 slave address is determined on
each I 2 C transmission, regardless of whether or not the
transmission is actually addressing the device. The
MAX7302 distinguishes whether address input AD0 is
connected to SDA, SCL, V DD , or GND during the trans-
mission. Therefore, the MAX7302 slave address can be
configured dynamically in an application without tog-
gling the device supply.
I/O Port Registers
The port I/O registers set the I/O ports, one register per
port (see Tables 6 and 7). Ports can be independently
configured as inputs or outputs (D7), push-pull or open
drain (D6). Port P1 can only be configured as an input or
an open-drain output. The push-pull bit (D6) setting for
the port I/O register P1 is ignored.
I/O Input Port
Configure a port as an input by writing a logic-high to
the MSB (bit D7) of the port I/O register (see Table 6).
See Figure 1 for input port structure. To obtain the logic
Table 5. Slave Address Selection
level of the port input, read the port I/O register bit, D0.
This readback value is the instantaneous logic level at
the time of the read request if debounce is disabled for
the port (port I/O register bit D2 = 0), or the debounced
result if debounce is enabled for the port (port I/O reg-
ister bit D2 = 1).
I/O Output Port
Configure a port as an output by writing a logic-low to the
MSB (bit D7) of the port I/O register. See Figures 2 and 3
for output port structure. The device reads back the logic
level, PWM, or the blink setting of the port (see Table 7).
The MAX7302 monitors the logic level of ports configured
as CLA outputs (see the Configurable Logic Array (CLA)
section).
Port Supplies and Level Translation
The port supply, V LA , provides the logic supplies to all
push-pull I/O ports. Ports P2–P9 can be configured as
push-pull I/O ports (see Figure 3). V LA powers the logic-
high port output voltage sourcing the logic-high port load
current. V LA provides level translation capability for the
outputs and operates over a 1.62V to 5.5V voltage inde-
pendent of the MAX7302 power-supply voltage, V DD .
Each port set as an input can be configured to switch
midrail of either the V DD or the V LA port supplies.
Whenever the port supply reference is changed from V DD
AD0
DEVICE ADDRESS
to V LA , or vice versa, read the port register to clear any
CONNECTION
A6
A5
A4
A3
A2
A1
A0 R W
transition flag on the port.
GND
1
0
0
1
1
0
0
0
1
V DD
SCL
SDA
1
1
1
0
0
0
0
0
0
1
1
1
1
1
1
0
1
1
1
0
1
0 1
0 1
0 1
Table 6. Port I/O Registers (I/O Port Set as an Input, Registers 0x01/0x41 to 0x09/049)
REGISTER BIT
D7
D6
D5
D4, D3
D2
D1
D0
DESCRIPTION
Port I/O set bit
Port supply
reference
Transition interrupt
enable
Reserved bits
Debounce
Port transition state
(read only)
Port status
(read only)
VALUE
1
0
1
0
1
0
0
1
0
1
0
1
FUNCTION
Sets the I/O port as an input.
Refers the input to the V LA supply voltage.
Refers the input to the V DD supply voltage.
Disables the transition interrupt.
Enables the transition interrupt.
Do not write to these registers.
Disables debouncing of the input port.
Enables debouncing of the input port.
No transition has occurred since the last port read.
A transition has occurred since the last port read.
Port input is logic-low.
Port input is logic-high.
10
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| GBC10DCAD | CONN EDGECARD 20POS R/A .100 SLD |
| EBC28DCSN-S288 | CONN EDGECARD 56POS .100 EXTEND |
| MAX6964ATG+ | IC LED DRIVER LINEAR 24-TQFN |
| MAX8647ETE+ | IC LED DRVR WT/RGB BCKLGT 16TQFN |
| EEC19DRXI | CONN EDGECARD 38POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX7302AEE+ | 功能描述:外围驱动器与原件 - PCI 9-Port Level-Trans GPIO & LED Driver RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| MAX7302AEE+T | 功能描述:外围驱动器与原件 - PCI 9-Port Level-Trans GPIO & LED Driver RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| MAX7302ATE | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:SMBus/I2C Interfaced 9-Port, Level-Translating GPIO and LED Driver with CLA |
| MAX7302ATE/GH9 | 制造商:Maxim Integrated Products 功能描述:LEVEL-TRANSLATING GPIO AND LED DRIVER WITH CLA - Rail/Tube |
| MAX7302ATE+ | 功能描述:外围驱动器与原件 - PCI 9-Port Level-Trans GPIO & LED Driver RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。