- 您现在的位置：买卖IC网 > PDF目录3767 > MAX7313AEG+T (Maxim Integrated Products)IC I/O EXPANDER I2C 16B 24QSOP PDF资料下载
参数资料
| 型号： | MAX7313AEG+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 25/26页 |
| 文件大小： | 0K |
| 描述： | IC I/O EXPANDER I2C 16B 24QSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 接口： | I²C |
| 输入/输出数： | 16 |
| 中断输出： | 是 |
| 频率 - 时钟： | 400kHz |
| 电源电压： | 2 V ~ 3.6 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 24-QSOP |
| 包装： | 带卷 (TR) |
MAX7313
only as an input. A pullup resistor, typically 4.7k
, is
required on SCL if there are multiple masters on the 2-
wire interface, or if the master in a single-master system
has an open-drain SCL output.
Each transmission consists of a START condition
(Figure 3) sent by a master, followed by the MAX7313
7-bit slave address plus R/W bit, a register address
byte, one or more data bytes, and finally a STOP condi-
tion (Figure 3).
START and STOP Conditions
Both SCL and SDA remain high when the interface is
not busy. A master signals the beginning of a transmis-
sion with a START (S) condition by transitioning SDA
from high to low while SCL is high. When the master
has finished communicating with the slave, it issues a
STOP (P) condition by transitioning SDA from low to
high while SCL is high. The bus is then free for another
transmission (Figure 3).
Bit Transfer
One data bit is transferred during each clock pulse.
The data on SDA must remain stable while SCL is high
(Figure 4).
Acknowledge
The acknowledge bit is a clocked 9th bit that the recipi-
ent uses to handshake receipt of each byte of data
(Figure 5). Thus, each byte transferred effectively
requires 9 bits. The master generates the 9th clock
pulse, and the recipient pulls down SDA during the
acknowledge clock pulse so the SDA line is stable low
during the high period of the clock pulse. When the
master is transmitting to the MAX7313, the device gen-
erates the acknowledge bit because the MAX7313 is
the recipient. When the MAX7313 is transmitting to the
master, the master generates the acknowledge bit
because the master is the recipient.
Slave Address
The MAX7313 has a 7-bit long slave address (Figure 6).
The eighth bit following the 7-bit slave address is the
R/W bit. The R/W bit is low for a write command, high
for a read command.
The slave address bits A6 through A0 are selected by
the address inputs AD0, AD1, and AD2. These pins can
be connected to GND, V+, SDA, or SCL. The MAX7313
has 64 possible slave addresses (Table 1) and, there-
fore, a maximum of 64 MAX7313 devices can be con-
trolled independently from the same interface.
Message Format for Writing the MAX7313
A write to the MAX7313 comprises the transmission of
the MAX7313’s slave address with the R/W bit set to
zero, followed by at least 1 byte of information. The first
byte of information is the command byte. The command
byte determines which register of the MAX7313 is to be
written to by the next byte, if received (Table 2). If a
STOP condition is detected after the command byte is
received, then the MAX7313 takes no further action
beyond storing the command byte.
16-Port I/O Expander with LED Intensity
Control, Interrupt, and Hot-Insertion Protection
8
_______________________________________________________________________________________
Figure 3. START and STOP Conditions
SDA
SCL
START
CONDITION
STOP
CONDITION
SP
Figure 4. Bit Transfer
SDA
SCL
DATA LINE STABLE;
DATA VALID
CHANGE OF DATA
ALLOWED
Figure 5. Acknowledge
SCL
SDA BY
TRANSMITTER
CLOCK PULSE
FOR ACKNOWLEDGE
START
CONDITION
SDA BY
RECEIVER
12
89
S
Figure 6. Slave Address
SDA
SCL
A5
MSB
LSB
ACK
A4
A1
A6
A3
A0
A2
R/W
相关PDF资料 |
PDF描述 |
|---|---|
| MAX7322ATE+ | IC I/O EXPANDER I2C 4B 16TQFN-EP |
| MAX7310AEE+ | IC I/O EXPANDER I2C 8B 16QSOP |
| ATMEGA8515L-8AUR | MCU AVR 8KB FLASH 8MHZ 44TQFP |
| MAX7316ATE+T | IC I/O EXPANDER I2C 16B 16TQFN |
| MAX7316AEE+ | IC I/O EXPANDER I2C 16B 16QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX7313ATG | 功能描述:接口-I/O扩展器 16-Bit I/O Port Expander RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
| MAX7313ATG+ | 功能描述:接口-I/O扩展器 16-Bit I/O Port Expander RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
| MAX7313ATG+T | 功能描述:接口-I/O扩展器 16-Bit I/O Port Expander RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
| MAX7313ATG-T | 功能描述:接口-I/O扩展器 16-Bit I/O Port Expander RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
| MAX7313DAEG+ | 功能描述:IC EXPANDER 16PORT 24QSOP RoHS:是 类别:集成电路 (IC) >> 接口 - I/O 扩展器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:74 系列:- 接口:I²C，JTAG 输入/输出数:9 中断输出:无 频率 - 时钟:400kHz 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:20-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:20-TSSOP 包装:管件 包括:EEPROM |
发布紧急采购，3分钟左右您将得到回复。