- 您现在的位置：买卖IC网 > PDF目录11710 > MAX7349ATG+T (Maxim Integrated Products)IC CNTRL SW SOUND 24-TQFN PDF资料下载
参数资料
| 型号： | MAX7349ATG+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 2/29页 |
| 文件大小： | 0K |
| 描述： | IC CNTRL SW SOUND 24-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 应用： | 声卡，播放器，记录器 |
| 接口： | I²C |
| 电源电压： | 2.4 V ~ 3.6 V |
| 封装/外壳： | 24-WFQFN 裸露焊盘 |
| 供应商设备封装： | 24-TQFN-EP（4x4） |
| 包装： | 带卷 (TR) |
| 安装类型： | 表面贴装 |
第1页当前第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
MAX7347/MAX7348/MAX7349
2-Wire Interfaced Low-EMI Key Switch
and Sounder Controllers
10
______________________________________________________________________________________
Bus Timeout
The MAX7347/MAX7348/MAX7349 feature a 20ms mini-
mum bus timeout on the 2-wire serial interface, largely to
prevent the MAX7347/MAX7348/MAX7349 from holding
the SDA I/O low during a read transaction if the SCL
hangs for any reason before a serial transaction has
been completed. Bus timeout operates by causing the
MAX7347/MAX7348/MAX7349 to internally terminate a
serial transaction, either read or write, if the time between
adjacent edges on SCL exceeds 20ms. After a bus time-
out, the MAX7347/MAX7348/MAX7349 wait for a valid
START condition before responding to a consecutive
transmission. The bus timeout feature requires the serial
interface to operate above 50Hz bus speed. This feature
can be enabled or disabled under user control by writing
to the configuration register (Table 12).
Message Format for Writing the
Key-Scan Controller
A write to the MAX7347/MAX7348/MAX7349s’ key-scan
controller
comprises
the
transmission
of
the
MAX7347/MAX7348/MAX7349s’ key-scan slave address
with the R/W bit set to zero, followed by at least 1 byte of
information. The first byte of information is the command
byte. The command byte determines which register of the
MAX7347/MAX7348/MAX7349 is to be written by the next
byte, if received. If a STOP condition is detected after the
command byte is received, then the MAX7347/MAX7348
/MAX7349 take no further action (Figure 7) beyond stor-
ing the command byte.
Any bytes received after the command byte are data
bytes. The first data byte goes into the internal register
of the MAX7347/MAX7348/MAX7349 selected by the
command byte (Figure 8).
If multiple data bytes are transmitted before a STOP
condition is detected, these bytes are generally stored
in subsequent MAX7347/MAX7348/MAX7349 internal
registers (Table 7) because the command byte address
generally autoincrements (Table 4).
Message Format for Reading the
Key-Scan Controller
The MAX7347/MAX7348/MAX7349 are read using the
MAX7347/MAX7348/MAX7349s’ internally stored com-
mand byte as an address pointer, the same way the
stored command byte is used as an address pointer for
a write. The pointer generally autoincrements after each
data byte is read using the same rules as for a write
(Table 4). Thus, a read is initiated by first configuring
the MAX7347/MAX7348/MAX7349s’ command byte by
performing a write (Figure 7). The master can now read
n consecutive bytes from the MAX7347/MAX7348/
MAX7349, with the first data byte being read from the
register addressed by the initialized command byte.
When performing read-after-write verification, remem-
ber to reset the command byte’s address because the
stored command byte address is generally autoincre-
mented after the write (Figure 9, Table 4).
SDA
SCL
01
1
A3
A2
A1
1
MSB
LSB
ACK
R/W
Figure 6. Slave Address
SCL
SDA
BY
TRANSMITTER
CLOCK PULSE FOR
ACKNOWLEDGE
START
CONDITION
SDA
BY
RECEIVER
1
2
8
9
S
Figure 5. Acknowledge
相关PDF资料 |
PDF描述 |
|---|---|
| VE-J54-IW-F2 | CONVERTER MOD DC/DC 48V 100W |
| VE-B6V-IW-F4 | CONVERTER MOD DC/DC 5.8V 100W |
| VE-B6V-IW-F3 | CONVERTER MOD DC/DC 5.8V 100W |
| VE-B6W-IW-F4 | CONVERTER MOD DC/DC 5.5V 100W |
| VE-B6W-IW-F3 | CONVERTER MOD DC/DC 5.5V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX7349EVKIT | 功能描述:接口 - 专用 Evaluation Kit for the MAX7349/Emulates: MAX7347/MAX7348 RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| MAX734C/D | 功能描述:直流/直流开关调节器 +12V 120mA Flash Memory Programming Supply RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX734C/D DIE | 制造商:Maxim Integrated Products 功能描述: |
| MAX734CPA | 功能描述:直流/直流开关调节器 12V 120mA Flash Mem Programming Supply RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX734CPA+ | 功能描述:直流/直流开关调节器 12V 120mA Flash Mem Programming Supply RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
发布紧急采购，3分钟左右您将得到回复。