- 您现在的位置：买卖IC网 > PDF目录11016 > MAX7420EUA+T (Maxim Integrated Products)IC FILTER LOWPASS 5TH 8UMAX PDF资料下载
参数资料
| 型号： | MAX7420EUA+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 2/14页 |
| 文件大小： | 0K |
| 描述： | IC FILTER LOWPASS 5TH 8UMAX |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 滤波器类型： | 巴特沃斯，低通开关电容器 |
| 频率 - 截止或中心： | 45kHz |
| 滤波器数： | 1 |
| 滤波器阶数： | 5th |
| 电源电压： | 4.5 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-uMAX |
| 包装： | 带卷 (TR) |
| 配用： | MAXFILTERBRD+-ND - BOARD EVAL MAX7408/7415/418-7425 |
MAX7418–MAX7425
5th-Order, Lowpass,
Switched-Capacitor Filters
10
______________________________________________________________________________________
An SCF that emulates a passive ladder filter retains
many of the same advantages. The component sensi-
tivity of a passive ladder filter is low when compared to
a cascaded biquadratic design because each compo-
nent affects the entire filter shape rather than a single
pole-zero pair. In other words, a mismatched compo-
nent in a biquadratic design has a concentrated error
on its respective poles, while the same mismatch in a
ladder filter design spreads its error over all poles.
Elliptic Characteristics
Lowpass elliptic filters such as the MAX7418/MAX7421/
MAX7422/MAX7425 provide the steepest possible
rolloff with frequency of the four most common filter
types (Butterworth, Bessel, Chebyshev, and elliptic).
The high-Q value of the poles near the passband edge
combined with the stopband zeros allow for the sharp
attenuation characteristic of elliptic filters, making these
devices ideal for anti-aliasing and post-DAC filtering in
single-supply systems (see
Anti-Aliasing and Post-DAC
Filtering).
In the frequency domain, the first transmission zero
causes the filter’s amplitude to drop to a minimum level
(Figure 2). Beyond this zero, the response rises as the
frequency increases until the next transmission zero.
The stopband begins at the stopband frequency, fS. At
frequencies above fS, the filter’s gain does not exceed
the gain at fS. The corner frequency, fC, is defined as
the point at which the filter output attenuation falls just
below the passband ripple. The transition ratio (r) is
defined as the ratio of the stopband frequency to the
corner frequency:
r = fS / fC
The MAX7418/MAX7422 have a transition ratio of 1.6
and typically 53dB of stopband rejection. The
MAX7421/MAX7425 have a transition ratio of 1.25 (pro-
viding a steeper rolloff) and typically 37dB of stopband
rejection.
Bessel Characteristics
Lowpass Bessel filters such as the MAX7419/MAX7423
delay all frequency components equally, preserving the
line up shape of step inputs (subject to the attenuation
of the higher frequencies). Bessel filters settle quickly—
an important characteristic in applications that use a
multiplexer (mux) to select an input signal for an ana-
log-to-digital converter (ADC). An anti-aliasing filter
placed between the mux and the ADC must settle
quickly after a new channel is selected.
Butterworth Characteristics
Lowpass Butterworth filters such as the MAX7420/
MAX7424 provide a maximally flat passband response,
making them ideal for instrumentation applications that
require minimum deviation from the DC gain throughout
the passband.
The difference between Bessel and Butterworth filters
can be observed when a 1kHz square wave is applied
to the filter input (Figure 3, trace A). With the filter cutoff
frequencies set at 5kHz, trace B shows the Bessel filter
response and trace C shows the Butterworth filter
response.
Clock Signal
External Clock
These SCFs are designed for use with external clocks
that have a 40% to 60% duty cycle. When using an
external clock, drive the CLK pin with a CMOS gate
powered from 0 to VDD. Varying the rate of the external
clock adjusts the corner frequency of the filter:
f
C
CLK
=
100
L4
C5
C3
C1
VIN
+
-
RL
L2
RS
Figure 1. 5th-Order Ladder Filter Network
PASSBAND
STOPBAND
GAIN
(dB)
FREQUENCY
fC
fS
fC
fS
fC
TRANSITION RATIO =
RIPPLE
Figure 2. Elliptic Filter Response
相关PDF资料 |
PDF描述 |
|---|---|
| MC9S08SH4MTGR | MCU 8BIT 4K FLASH 16-TSSOP |
| MC9S08MP12VWL | MCU 8BIT .25U SGF FLASH SOIC |
| MAX7418EUA+T | IC FILTER LOWPASS 5TH 8UMAX |
| MC908QT2ACDWER | IC MCU 8BIT 1.5K FLASH 8-SOIC |
| MCHC908QT2CDWER | IC MCU 1.5K FLASH W/ADC 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX7421CUA | 功能描述:有源滤波器 RoHS:否 制造商:Maxim Integrated 通道数量:1 截止频率:150 KHz 电源电压-最大:11 V 电源电压-最小:4.74 V 最大工作温度:+ 85 C 安装风格:Through Hole 封装 / 箱体:PDIP N 封装:Tube |
| MAX7421CUA+ | 功能描述:有源滤波器 5th-Order Lowpass Elliptic Filter RoHS:否 制造商:Maxim Integrated 通道数量:1 截止频率:150 KHz 电源电压-最大:11 V 电源电压-最小:4.74 V 最大工作温度:+ 85 C 安装风格:Through Hole 封装 / 箱体:PDIP N 封装:Tube |
| MAX7421CUA+T | 功能描述:有源滤波器 5th-Order Lowpass Elliptic Filter RoHS:否 制造商:Maxim Integrated 通道数量:1 截止频率:150 KHz 电源电压-最大:11 V 电源电压-最小:4.74 V 最大工作温度:+ 85 C 安装风格:Through Hole 封装 / 箱体:PDIP N 封装:Tube |
| MAX7421CUA-T | 功能描述:有源滤波器 RoHS:否 制造商:Maxim Integrated 通道数量:1 截止频率:150 KHz 电源电压-最大:11 V 电源电压-最小:4.74 V 最大工作温度:+ 85 C 安装风格:Through Hole 封装 / 箱体:PDIP N 封装:Tube |
| MAX7421EUA | 功能描述:有源滤波器 RoHS:否 制造商:Maxim Integrated 通道数量:1 截止频率:150 KHz 电源电压-最大:11 V 电源电压-最小:4.74 V 最大工作温度:+ 85 C 安装风格:Through Hole 封装 / 箱体:PDIP N 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。