- 您现在的位置：买卖IC网 > PDF目录14500 > MAX763ACSA+ (Maxim Integrated Products)IC REG BUCK 3.3V 0.5A 8SOIC PDF资料下载
参数资料
| 型号： | MAX763ACSA+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 6/12页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK 3.3V 0.5A 8SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 100 |
| 类型： | 降压（降压） |
| 输出类型： | 固定 |
| 输出数： | 1 |
| 输出电压： | 3.3V |
| 输入电压： | 3.3 V ~ 11 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 200kHz |
| 电流 - 输出： | 500mA |
| 同步整流器： | 无 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 管件 |
| 供应商设备封装： | 8-SOIC |
3.3V, Step-Down,
Current-Mode PWM DC-DC Converters
_______________________________________________________________________Pin Description
PIN #
8-PIN DIP/SO
1
2
3
4
5
6
7
16-PIN WIDE SO
(MAX748A)
2
3
7
8
9
10, 11
12, 13, 14
NAME
SHDN
REF
SS
CC
OUT
GND
LX
FUNCTION
Shutdown—active low. Connect to ground to power down chip; tie to V+ for normal
operation. Output voltage falls to 0V when SHDN is low.
Reference Voltage Output (+1.23V) supplies up to 100μA for external loads.
Bypass to GND with a 0.047μF capacitor.
Soft-Start. Capacitor between SS and GND provides soft-start and
short-circuit protection.
Compensation Capacitor Input externally compensates the outer (voltage)
feedback loop. Connect to OUT with a 330pF capacitor.
Output-Voltage Sense Input provides regulation feedback sensing.
Connect to +3.3V output.
Ground*
Drain of internal P-channel power MOSFET*
Supply Voltage Input. Bypass to GND with 1μF ceramic and large-value
8
1,15,16
V+
electrolytic capacitor in parallel. The 1μF capacitor must be as close
to the GND and V+ pins as possible.*
4, 5, 6
N.C.
No Connect—no internal connections to these pins.
*16-pin wide SO package: All pins sharing the same name must be connected together externally.
_________________Detailed Description
The MAX748A/MAX763A switch-mode regulators use a
current-mode pulse-width-modulation (PWM) control
system in a step-down (buck) regulator topography.
They convert an unregulated DC input voltage from 4V
to 11V (MAX763A) or from 4V to 16V (MAX748A) to a
regulated 3.3V output at 300mA. For loads less than
300mA, V+ may be less than 4.0V (see the Output
Voltage vs. Supply Voltage graph in the Typical
Operating Characteristics ). The current-mode
PWM architecture provides cycle-by-cycle current limit-
ing, improved load-transient response, and simpler
outerloop design.
The controller consists of two feedback loops: an inner
(current) loop that monitors the switch current via the
current-sense resistor and amplifier, and an outer (volt-
age) loop that monitors the output voltage through the
error amplifier (Figure 1). The inner loop performs
cycle-by-cycle current limiting, truncating the power
transistor on-time when the switch current reaches a
predetermined threshold. This threshold is determined
by the outer loop. For example, a sagging output volt-
age produces an error signal that raises the threshold,
allowing the circuit to store and transfer more energy
during each cycle.
Programmable Soft-Start
Figure 2 shows a capacitor connected to the soft-start
(SS) pin to ensure orderly power-up. A typical value is
0.047μF. SS controls both the SS timing and the maxi-
mum output current that can be delivered while main-
taining regulation.
The charging capacitor slowly raises the clamp on the
error-amplifier output voltage, limiting surge currents
at power-up by slowly increasing the cycle-by-cycle
current-limit threshold. Table 1 lists timing characteris-
tics for selected capacitor values and circuit conditions.
The overcurrent comparator trips when the load exceeds
approximately 1.2A. When either an undervoltage or over-
current fault condition is detected, an SS cycle is actively
initiated, which triggers an internal transistor to discharge
the SS capacitor to ground. An SS cycle is also enabled
at power-up and when coming out of shutdown mode.
Overcurrent Limiting
The overcurrent comparator triggers when the load
current exceeds approximately 1.2A. On each clock
cycle, the output FET turns on and attempts to deliver
current until cycle-by-cycle or overcurrent limits are
exceeded. Note that the SS capacitor must be greater
than 0.01μF for overcurrent protection to function prop-
erly. A typical value is 0.047μF.
6
_______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| ECA43DTMN | CONN EDGECARD 86POS R/A .125 SLD |
| LGN2V561MELB45 | CAP ALUM 560UF 350V 20% SNAP |
| VI-B13-EW-F1 | CONVERTER MOD DC/DC 24V 100W |
| ECA43DTMH | CONN EDGECARD 86POS R/A .125 SLD |
| IHSM7832PJ183L | INDUCTOR POWER 18MH 0.11A SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX763ACSA+ | 功能描述:直流/直流开关转换器 3.3V Step-Down DC/DC Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX763ACSA+T | 功能描述:直流/直流开关转换器 3.3V Step-Down DC/DC Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX763ACSA-T | 功能描述:直流/直流开关转换器 3.3V Step-Down DC/DC Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX763ACSA-TG068 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX763AEPA | 功能描述:直流/直流开关转换器 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。