参数资料
型号: MAX772CSA+
厂商: Maxim Integrated Products
文件页数: 14/20页
文件大小: 0K
描述: IC REG CTRLR BST PWM 8-SOIC
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 100
PWM 型: 控制器
输出数: 1
频率 - 最大: 300kHz
占空比: 90%
电源电压: 3 V ~ 16.5 V
降压:
升压:
回扫:
反相:
倍增器:
除法器:
Cuk:
隔离:
工作温度: 0°C ~ 70°C
封装/外壳: 8-SOIC(0.154",3.90mm 宽)
包装: 管件
5V/12V/15V or Adjustable, High-Efficiency,
Low I Q , Step-Up DC-DC Controllers
Table 1. Bootstrapped vs. Non-Bootstrapped Operation
PARAMETER
Gate Drive
FET On Resistance
Gate-Drive Capacitive Losses
No-Load Supply Current
Possible Input Voltage Range
Normally Recommended Input
Voltage Range
Fixed Output Available
Adjustable Output Available
BOOTSTRAPPED*
GND to V OUT
Lower
Higher
Higher
2V to 16.5V (MAX770/MAX771/MAX772),
(internal feedback resistors)
3V to 16.5V (MAX770/MAX771/MAX772),
(external feedback resistors)
3V to 16.5V (MAX773)
2V to 5V (MAX770/MAX771/MAX772),
3V to 5V (MAX773)
MAX770–MAX773(N)
MAX770–MAX773(N)
NON-BOOTSTRAPPED
GND to V+
Higher
Lower
Lower
3V to 16.5V
(MAX770/MAX771/MAX772),
3V and up (MAX773)
5V to 16.5V
(MAX770/MAX771/MAX772),
5V and up (MAX773)
MAX773(N)/MAX773(S)
MAX770/MAX771/MAX772/
MAX773(N)/MAX773(S)
*MAX773(S) indicates shunt mode; MAX773(N) indicates NOT in shunt mode.
Use an N-channel FET as the power switch when using
the shunt regulator (see MAX773 Shunt-Regulator
V IN
Operation in the Detailed Description). The shunt-regu-
lator current powers the MAX773 and also provides the
FET gate-drive current, which depends largely on the
R SHUNT
C2
0.1 μ F
C1
FET’s total gate charge at V GS = 5V. To determine the
shunt-resistor value, first determine the maximum shunt
current required.
I SHUNT = I SUPP + I GATE
3
V+
SGND
EXTH
10
13
NPN
2N2222A
L1
20 μ H
D1
V OUT
See N-Channel MOSFETs in the Power-Transistor
Selection section to determine I GATE .
Determine the shunt-resistor value using the following
equation:
MAX773
EXTL
12
100 ?
PNP
2N2907A
N
R2
C4
V IN (min) - V SHUNT (max)
R SHUNT (max) = ————————————
I SHUNT
where V SHUNT (max) is 6.3V.
The shunt regulator is not disabled in shutdown
CS
FB
11
6
R SENSE
R1
mode, and continues to draw the calculated shunt
current.
If the calculated shunt regulator current exceeds 20mA,
or if the shunt current exceeds 5mA and less shunt reg-
ulator current is desired, use the circuit of Figure 6 to
provide increased drive and reduced shunt current
when driving N-FETs with large gate capacitances.
Select I SHUNT = 3mA. This provides adequate biasing
current for this circuit, although higher shunt currents
can be used.
Figure 6. Increased N-FET Gate Drive when Using the Shunt
Regulator
To prevent the shunt regulator from drawing current in
shutdown mode, place a switch in series with the shunt
resistor.
14
______________________________________________________________________________________
相关PDF资料
PDF描述
ISL88013IH531Z-TK IC VOLTAGE MONITOR DUAL SOT23-5
MAX608ESA+T IC REG CTRLR BST PWM 8-SOIC
MAX608EPA+ IC REG CTRLR BST PWM 8-PDIP
MAX1651CSA+T IC REG CTRLR BUCK PWM 8-SOIC
MAX1649CSA+T IC REG CTRLR BUCK PWM 8-SOIC
相关代理商/技术参数
参数描述
MAX772CSA+ 功能描述:DC/DC 开关控制器 5/12/15/AdjV Step Up DC/DC Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK
MAX772CSA+T 功能描述:DC/DC 开关控制器 5/12/15/AdjV Step Up DC/DC Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK
MAX772CSA-T 功能描述:DC/DC 开关控制器 5/12/15/AdjV Step Up DC/DC Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK
MAX772EPA 功能描述:DC/DC 开关控制器 5/12/15/AdjV Step Up DC/DC Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK
MAX772ESA 功能描述:DC/DC 开关控制器 5/12/15/AdjV Step Up DC/DC Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK