参数资料
型号: MAX791CSE
厂商: Maxim Integrated Products
文件页数: 16/19页
文件大小: 0K
描述: IC MPU SUPERVISOR CIRCUIT 16SOIC
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 50
类型: 备用电池电路
监视电压数目: 1
输出: 推挽式,图腾柱
复位: 低有效
复位超时: 最小为 140 ms
电压 - 阀值: 4.65V
工作温度: 0°C ~ 70°C
安装类型: 表面贴装
封装/外壳: 16-SOIC(0.154",3.90mm 宽)
供应商设备封装: 16-SOIC
包装: 管件
Microprocessor Supervisory Circuit
+5V
R1
PFI
V CC
PFO
100
80
V CC = +5V
T A = +25°C
0.1 μ F CAPACITOR
FROM V OUT TO GND
R2
MAX791
GND
60
40
+5V
PFO
V-
20
0V
0
10
100
1000
10,000
5 - 1.25 = 1.25 - V TRIP
R1 R2
V TRIP
V-
0V
RESET COMPARATOR OVERDRIVE (mV)
(Reset Threshold Voltage - V CC )
NOTE : V TRIP IS NEGATIVE
Figure 15. Monitoring a Negative Voltage
close to SWT as possible. The sum of PC board leak-
age + SWT capacitor leakage must be small compared
to ±100nA.
Watchdog Software Considerations
A way to help the watchdog timer keep a closer watch
on software execution involves setting and resetting the
watchdog input at different points in the program,
rather than “pulsing” the watchdog input high-low-high
or low-high-low. This technique avoids a “stuck” loop
where the watchdog timer continues to be reset within
the loop, keeping the watchdog from timing out.
Figure 17 shows an example flow diagram where the
I/O driving the watchdog input is set high at the begin-
ning of the program, set low at the beginning of every
subroutine or loop, then set high again when the pro-
Figure 16. Maximum Transient Duration Without Causing a
Reset Pulse vs. Reset Comparator Overdrive
gram returns to the beginning. If the program should
“hang” in any subroutine, the I/O is continually set low
and the watchdog timer is allowed to time out, causing
a reset or interrupt to be issued.
Maximum V CC Fall Time
The V CC fall time is limited by the propagation delay of
the battery switchover comparator and should not
exceed 0.03V/μs. A standard rule of thumb for filter
capacitance on most regulators is on the order of
100μF per amp of current. When the power supply is
shut off or the main battery is disconnected, the associ-
ated initial V CC fall rate is just the inverse or 1A / 100μF
= 0.01V/μs. The V CC fall rate decreases with time as
V CC falls exponentially, which more than satisfies the
maximum fall-time requirement.
16
______________________________________________________________________________________
相关PDF资料
PDF描述
MAX792MCPE IC MPU SUPRVSRY CIRC 4.37V 16DIP
MAX793SESE IC MPU SUPERVISORY CIRC 16SOIC
MAX797CSE-T IC REG CTRLR BUCK PWM CM 16-SOIC
MAX797HESE+T IC REG CTRLR BUCK PWM 16-SOIC
MAX798ESE+T IC REG CTRLR BUCK PWM CM 16-SOIC
相关代理商/技术参数
参数描述
MAX791CSE+ 功能描述:监控电路 MPU Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟(典型值):10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel
MAX791CSE+T 功能描述:监控电路 MPU Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟(典型值):10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel
MAX791CSE-T 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟(典型值):10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel
MAX791CUE 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟(典型值):10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel
MAX791CUE+ 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟(典型值):10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel