参数资料
型号: MAX801MCPA+
厂商: Maxim Integrated Products
文件页数: 12/12页
文件大小: 0K
描述: IC SUPERVISOR MPU 8-DIP
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 50
类型: 备用电池电路
监视电压数目: 1
复位: 高有效/低有效
复位超时: 最小为 140 ms
电压 - 阀值: 4.425V
工作温度: 0°C ~ 70°C
安装类型: 通孔
封装/外壳: 8-DIP(0.300",7.62mm)
供应商设备封装: 8-PDIP
包装: 管件
8-Pin μP Supervisory Circuits
with ±1.5% Reset Accuracy
Watchdog Software Considerations
To help the watchdog timer keep a closer watch on
software execution, you can set and reset the watch-
dog input at different points in the program, rather than
“pulsing” the watchdog input high-low-high or low-high-
low. This technique avoids a “stuck” loop, where the
watchdog timer continues to be reset within the loop,
keeping the watchdog from timing out.
Figure 9 shows a sample flow diagram where the I/O
driving the watchdog input is set high at the beginning
of the program, low at the beginning of every subrou-
tine or loop, then high again when the program returns
to the beginning. If the program should “hang” in any
subroutine, the I/O would be continually set low and the
watchdog timer would be allowed to time out, causing a
reset or interrupt to be issued.
Maximum V CC Fall Time
The V CC fall time is limited by the propagation delay of
the battery switchover comparator and should not
exceed 0.03V/μs. A standard rule for filter capacitance
on most regulators is around 100μF per Ampere of cur-
rent. When the power supply is shut off or the main bat-
tery is disconnected, the associated initial V CC fall rate
is just the inverse, or 1A/100μF = 0.01V/μs.
_________________Pin Configurations
TOP VIEW
START
SET
WDI
LOW
SUBROUTINE
OR PROGRAM LOOP,
SET WDI
HIGH
RETURN
END
Figure 9. Watchdog Flow Diagram
___________________Chip Information
TRANSISTOR COUNT: 922
V CC 1
8
OUT
LOWLINE 2
RESET 3
GND 4
MAX801
7
6
5
BATT
WDI
RESET
DIP/SO
V CC 1
8
OUT
LOWLINE 2
RESET 3
GND 4
MAX808
7
6
5
BATT
CE IN
CE OUT
DIP/SO
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
12 __________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 (408) 737-7600
? 2005 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products, Inc.
相关PDF资料
PDF描述
RGM12DTBS-S189 CONN EDGECARD 24POS R/A .156 SLD
GMA32DRSD-S288 CONN EDGECARD 64POS .125 EXTEND
MAX801NCPA+ IC SUPERVISOR MPU 8-DIP
RCM28DTBN-S189 CONN EDGECARD 56POS R/A .156 SLD
DS1238S-5+T&R IC MICROMAN W/FRESH 5% 16-SOIC
相关代理商/技术参数
参数描述
MAX801MCPA+ 功能描述:监控电路 8-Pim uPower Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟(典型值):10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel
MAX801MCSA 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟(典型值):10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel
MAX801MCSA+ 功能描述:监控电路 8-Pim uPower Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟(典型值):10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel
MAX801MCSA+T 功能描述:监控电路 8-Pim uPower Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟(典型值):10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel
MAX801MCSA-T 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟(典型值):10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel