- 您现在的位置：买卖IC网 > PDF目录15865 > MAX801NCSA+ (Maxim Integrated Products)IC SUPERVISOR MPU 8-SOIC PDF资料下载
参数资料
| 型号： | MAX801NCSA+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 12/12页 |
| 文件大小： | 0K |
| 描述： | IC SUPERVISOR MPU 8-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 100 |
| 类型： | 备用电池电路 |
| 监视电压数目： | 1 |
| 复位： | 高有效/低有效 |
| 复位超时： | 最小为 140 ms |
| 电压 - 阀值： | 4.575V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 管件 |
8-Pin μP Supervisory Circuits
with ±1.5% Reset Accuracy
Watchdog Software Considerations
To help the watchdog timer keep a closer watch on
software execution, you can set and reset the watch-
dog input at different points in the program, rather than
“pulsing” the watchdog input high-low-high or low-high-
low. This technique avoids a “stuck” loop, where the
watchdog timer continues to be reset within the loop,
keeping the watchdog from timing out.
Figure 9 shows a sample flow diagram where the I/O
driving the watchdog input is set high at the beginning
of the program, low at the beginning of every subrou-
tine or loop, then high again when the program returns
to the beginning. If the program should “hang” in any
subroutine, the I/O would be continually set low and the
watchdog timer would be allowed to time out, causing a
reset or interrupt to be issued.
Maximum V CC Fall Time
The V CC fall time is limited by the propagation delay of
the battery switchover comparator and should not
exceed 0.03V/μs. A standard rule for filter capacitance
on most regulators is around 100μF per Ampere of cur-
rent. When the power supply is shut off or the main bat-
tery is disconnected, the associated initial V CC fall rate
is just the inverse, or 1A/100μF = 0.01V/μs.
_________________Pin Configurations
TOP VIEW
START
SET
WDI
LOW
SUBROUTINE
OR PROGRAM LOOP,
SET WDI
HIGH
RETURN
END
Figure 9. Watchdog Flow Diagram
___________________Chip Information
TRANSISTOR COUNT: 922
V CC 1
8
OUT
LOWLINE 2
RESET 3
GND 4
MAX801
7
6
5
BATT
WDI
RESET
DIP/SO
V CC 1
8
OUT
LOWLINE 2
RESET 3
GND 4
MAX808
7
6
5
BATT
CE IN
CE OUT
DIP/SO
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
12 __________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 (408) 737-7600
? 2005 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products, Inc.
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6439UTBHYD3+T | IC BATTERY MON SNGL SOT23-6 |
| 5-1879291-6 | CAP ALUM 1UF 50V 20% SMD |
| ISC1210SY6R8J | INDUCTOR WW 6.8UH 5% 1210 |
| MAX6795TPLD2+ | IC REG LIN W/SPR VSR 20-TQFN |
| 4-1879291-2 | CAP ALUM 4.7UF 35V 20% SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX801NCSA+ | 功能描述:监控电路 8-Pim uPower Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX801NCSA+T | 功能描述:监控电路 8-Pim uPower Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX801NCSA-T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX801NEPA | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX801NEPA+ | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。