参数资料
| 型号： | MAX810TTR |
| 厂商： | ON Semiconductor |
| 文件页数： | 8/13页 |
| 文件大小： | 0K |
| 描述： | IC MPU SUPERVISORY 3.08V SOT23 |
| 产品变化通告： | LTB Notification 03/Jan/2008 |
| 标准包装： | 1 |
| 类型： | 简单复位/加电复位 |
| 监视电压数目： | 1 |
| 输出： | 推挽式，图腾柱 |
| 复位： | 高有效 |
| 复位超时： | 最小为 140 ms |
| 电压 - 阀值： | 3.08V |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | TO-236-3，SC-59，SOT-23-3 |
| 供应商设备封装： | SOT-23-3（TO-236） |
| 包装： | 剪切带 (CT) |
| 其它名称： | MAX810TTROSCT |
MAX809 Series, MAX810 Series
Detail Operation Description
The MAX809/810 series microprocessor reset
supervisory circuits are designed to monitor the power
supplies in digital systems and provide a reset signal to the
processor without any external components. Figure 2 shows
the timing diagram and a typical application below. Initially
consider that input voltage V CC is at a nominal level greater
than the voltage detector upper threshold ( VTH ). And the
RESET (RESET) output voltage (Pin 2) will be in the high
state for MAX809, or in the low state for MAX 810 devices.
If there is an input power interruption and V CC becomes
significantly deficient, it will fall below the lower detector
threshold (V TH ? ). This event causes the RESET output to be
in the low state for the MAX809, or in the high state for the
NCP810 devices. After completion of the power
interruption, V CC will rise to its nominal level and become
greater than the V TH . This sequence activates the internal
oscillator circuitry and digital counter to count. After the
count of the timeout period, the reset output will revert back
to the original state.
Input Voltage
Reset Output
MAX809, NCP803
Reset Output
V CC
V TH+
V TH–
V CC
V TH–
0V
V CC
V TH–
MAX810
0V
t RP
Figure 15. Timing Waveforms
http://onsemi.com
8
相关PDF资料 |
PDF描述 |
|---|---|
| 63MXC2700MEFCSN25X30 | CAP ALUM 2700UF 63V 20% SNAP-IN |
| UWS1C221MCL1GS | CAP ALUM 220UF 16V 20% SMD |
| UWS1A471MCL1GS | CAP ALUM 470UF 10V 20% SMD |
| MAX809TTR | IC MPU SUPERVISORY 3.08V SOT23 |
| UWS1A331MCL1GS | CAP ALUM 330UF 10V 20% SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX810TTRG | 功能描述:监控电路 3.08V uP Reset RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX810TW | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:3-pin microprocessor resets |
| MAX810XD | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:3-pin microprocessor resets |
| MAX810XTR | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:3-Pin Microprocessor Reset Monitors |
| MAX810XW | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:3-pin microprocessor resets |
发布紧急采购，3分钟左右您将得到回复。