- 您现在的位置：买卖IC网 > PDF目录16768 > MAX8520ETP+ (Maxim Integrated Products)IC DRVR PWR TEC 20-TQFN PDF资料下载
参数资料
| 型号： | MAX8520ETP+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 13/18页 |
| 文件大小： | 0K |
| 描述： | IC DRVR PWR TEC 20-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 60 |
| 应用： | 热电冷却器 |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-WQFN 裸露焊盘 |
| 供应商设备封装： | 20-TQFN-EP（5x5） |
| 包装： | 管件 |
Smallest TEC Power Drivers for Optical
Modules
3/4 V DD
1/4 V DD
LX2
-1.2
PWM
REF
COMP
1.2X
4X
CTLI
1
gm
C COMP
R SENSE
R
0.5X
R
+1.2
CS
LX1
Figure 3. Functional Diagram of the Current-Control Loop
10X
OS1
Inductor Selection
Calculate the inductor value as follows:
The MAX8520/MAX8521 dual buck converters operate
in-phase and in complementary mode to drive the TEC
differentially in a current-mode control scheme. At zero
TEC current, the differential voltage is zero, hence the
L =
( 0 . 25 × V DD )
LIR × I TEC ( MAX ) × fs
outputs with respect to GND are equal to half of V DD .
As the TEC current demand increases, one output will
go up and the other will go down from the initial point of
0.5V DD by an amount equal to 0.5 V TEC (V TEC = I TEC
R TEC ). Therefore, the operating duty cycle of each
buck converter depends on the operating I TEC and
R TEC . Since inductor current calculation for heating and
cooling are identical, but reverse in polarity, the calcu-
lation only needs to be carried out for either one.
For a given inductor, and input voltage, the maximum
inductor ripple current happens when the duty cycle is
at 50%. Therefore, the inductor should be calculated at
50% duty cycle to find the maximum ripple current. The
maximum desired ripple current of a typical standard
buck converter is in the range of 20% to 40% of the
maximum load. The higher the value of the inductor, the
lower the ripple current. However, the size will be phys-
ically larger. For the TEC driver the thermal loop is
inherently slow, so the inductor can be larger for lower
ripple current for better noise and EMI performance.
Picking an inductor to yield ripple current of 10% to
20% of the maximum TEC current is a good starting
point.
where LIR is the selected inductor ripple-current ratio,
I TEC(MAX) is the maximum TEC current, and fs is the
switching frequency
As an example, for V DD = 3.3V, LIR = 12%, and fs =
1MHz, L = 4.58μH
Even though each inductor ripple current is at its maxi-
mum at 50% duty cycle (zero TEC current), the ripple
cancels differentially because each is equal and in-
phase.
Output Filter Capacitor Selection
Common-Mode Filter Capacitors
The common-mode filter capacitors (C2 and C7 of
Figure 1) are used as filter capacitors to ground for
each output. The output ripple voltage depends on the
capacitance, the ESR of these capacitors, and the
inductor ripple current. Ceramic capacitors are recom-
mended for their low ESR and impedance at high fre-
quency.
______________________________________________________________________________________
13
相关PDF资料 |
PDF描述 |
|---|---|
| ESM10DTKN | CONN EDGECARD 20POS DIP .156 SLD |
| NCP4896EVB | EVAL BOARD FOR NCP4896 |
| H8PPH-1418M | DIP CABLE - HDP14H/AE14M/HDP14H |
| HBC05DRES-S734 | CONN EDGECARD 10POS .100 EYELET |
| 462A046-4/42-0 | BOOT MOLDED |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8520ETP/GG8 | 制造商:Maxim Integrated Products 功能描述: |
| MAX8520ETP+ | 功能描述:显示驱动器和控制器 TEC Power Driver for Optical Modules RoHS:否 制造商:Panasonic Electronic Components 工作电源电压:2.7 V to 5.5 V 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Reel |
| MAX8520ETP+T | 功能描述:其他电源管理 TEC Power Driver for Optical Modules RoHS:否 制造商:Texas Instruments 输出电压范围: 输出电流:4 mA 输入电压范围:3 V to 3.6 V 输入电流: 功率耗散: 工作温度范围:- 40 C to + 110 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-48 封装:Reel |
| MAX8520ETP-T | 功能描述:其他电源管理 RoHS:否 制造商:Texas Instruments 输出电压范围: 输出电流:4 mA 输入电压范围:3 V to 3.6 V 输入电流: 功率耗散: 工作温度范围:- 40 C to + 110 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-48 封装:Reel |
| MAX8520EVKIT | 制造商:Maxim Integrated Products 功能描述:SMALLEST TEC POWER DRIVERS FOR OPTI - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。