- 您现在的位置：买卖IC网 > PDF目录20722 > MAX8530ETTK2+T (Maxim Integrated)IC REG LDO 2.8V/1.8V 6-TDFN PDF资料下载
参数资料
| 型号： | MAX8530ETTK2+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 8/12页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 2.8V/1.8V 6-TDFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 2.8V，1.8V |
| 输入电压： | 2.5 V ~ 6.5 V |
| 电压 - 压降（标准）： | 0.1V @ 100mA，- |
| 稳压器数量： | 2 |
| 电流 - 输出： | 200mA（最小），150mA（最小） |
| 电流 - 限制（最小）： | 210mA，165mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-WDFN 裸露焊盘 |
| 供应商设备封装： | 6-TDFN 裸露焊盘（3x3） |
| 包装： | 带卷 (TR) |
Dual Low-Dropout Linear Regulators
with RESET or Low-Noise Output in UCSP or QFN
Applications Information
Capacitor Selection
and Regulator Stability
Use a 2.2μF capacitor on the MAX8530/MAX8531s ’
inputs. Larger input capacitor values with lower ESRs
provide better supply-noise rejection and line-transient
response. To reduce noise and improve load transients,
use large-output capacitors, up to 10μF. For stable
operation over the full temperature range and with rated
maximum load currents, use a minimum of 2.2μF (or
1μF for <150mA loading for OUT1) and 1μF for OUT2.
Note that some ceramic dielectrics exhibit large capac-
itance and ESR variation with temperature. With
dielectrics such as Z5U and Y5V, it is necessary to use
4.7μF or more to ensure stability at temperatures below
-10°C. With X7R or X5R dielectrics, 2.2μF is sufficient at
all operating temperatures. These regulators are opti-
mized for ceramic capacitors. Tantalum capacitors are
not recommended.
PSRR and Operation from
Sources Other than Batteries
The MAX8530/MAX8531 is designed to deliver low
dropout voltages and low quiescent currents in battery-
powered systems. Power-supply rejection is 60dB at
low frequencies (see the Power-Supply Rejection Ratio
vs. Frequency graph in the Typical Operating Char-
acteristics ).
When operating from sources other than batteries,
improve supply-noise rejection and transient response
by increasing the values of the input and output bypass
capacitors and through passive filtering techniques.
Load-Transient Considerations
The MAX8530/MAX8531 load-transient response
graphs (see the Typical Operating Characteristics )
show two components of the output response: a DC
shift in the output voltage because of the different load
currents, and the transient response. Increase the output
capacitor’s value and decrease its ESR to attenuate
transient spikes.
Input/Output (Dropout Voltage)
A regulator’s minimum input/output voltage differential
(or dropout voltage) determines the lowest usable supply
voltage. In battery-powered systems, this determines
the useful end-of-life battery voltage. Because the
MAX8530/MAX8531 use a P-channel MOSFET pass
transistor, their dropout voltage is a function of drain-to-
source on-resistance (R DS(ON) ) multiplied by the load
current (see the Typical Operating Characteristics ).
Calculating the Maximum
Output Power in UCSP
The maximum output power of the MAX8530/MAX8531
can be limited by the maximum power dissipation of the
package. Obtain the maximum power dissipation by
calculating the power dissipation of the package as a
function of the input voltage, output voltage, and output
currents. The maximum power dissipation should not
exceed the package’s maximum power rating:
P = (V IN(MAX) - V OUT1 ) x I OUT1 +
(V IN(MAX) - V OUT2 ) x I OUT2
where:
V IN(MAX) = Maximum input voltage
P MAX = Maximum power dissipation of the package
(308mW for UCSP and 1951mW for the QFN package)
V OUT1 = Output voltage of OUT1
V OUT2 = Output voltage of OUT2
I OUT1 = Maximum output current of OUT1
I OUT2 = Maximum output current of OUT2
P should be less than P MAX . If P is greater than P MAX ,
consider using the QFN package.
8
_______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| ESM44DRYF | CONN EDGECARD 88POS DIP .156 SLD |
| B82442A1225K | INDUCTOR 2200UH 55MA 2220 10% |
| MAX1818EUT50#TG16 | IC REG LDO 5V/ADJ .5A SOT23-6 |
| VE-J3P-EW-B1 | CONVERTER MOD DC/DC 13.8V 100W |
| AISM-1210-R18M-T | INDUCTOR .18UH 20% 1210 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8530ETTKO | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX8530ETTKO-T | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX8530ETTM1 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX8530ETTM1-T | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX8530ETTO2 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
发布紧急采购，3分钟左右您将得到回复。