- 您现在的位置：买卖IC网 > PDF目录20712 > MAX8532EBT2+T (Maxim Integrated)IC REG LDO 1.8V .2A 6-UCSP PDF资料下载
参数资料
| 型号： | MAX8532EBT2+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 6/8页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 1.8V .2A 6-UCSP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 1.8V |
| 输入电压： | 2.5 V ~ 6.5 V |
| 稳压器数量： | 1 |
| 电流 - 输出： | 200mA（最小） |
| 电流 - 限制（最小）： | 210mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-WFBGA，CSPBGA |
| 供应商设备封装： | 6-uCSP（1.57x1.16） |
| 包装： | 带卷 (TR) |
Low-Noise, Low-Dropout,
200mA Linear Regulator in UCSP
Current Limit
The MAX8532 contains an independent current limiter,
which monitors and controls the pass transistor’s gate
voltage, limiting the output current to 210mA (min). The
output can be shorted to ground indefinitely without
damaging the part.
Thermal-Overload Protection
Thermal-overload protection limits total power dissipa-
tion in the MAX8532. When the junction temperature
exceeds T J = +160°C, the thermal sensor signals the
shutdown logic, turning off the pass transistor and allow-
ing the IC to cool. The thermal sensor turns the pass
transistor on again after the IC’s junction temperature
cools by 10°C, resulting in a pulsed output during contin-
uous thermal-overload conditions.
Thermal-overload protection is designed to protect the
MAX8532 in the event of fault conditions. For continual
operation, do not exceed the absolute maximum junc-
tion temperature rating of T J = +150°C.
Operating Region and Power Dissipation
The MAX8532’s maximum power dissipation depends
on the thermal resistance of the case and circuit board,
the temperature difference between the die junction
and ambient air, and the airflow rate. The power dissi-
pation across the device is P = I OUT (V IN - V OUT ).
Maximum power dissipation:
P MAX = (T J - T A )/( θ JB + θ BA )
where T J - T A is the temperature difference between the
MAX8532 die junction and the surrounding air, θ JB (or
θ JC ) is the thermal resistance of the package, and θ BA is
the thermal resistance through the printed circuit board,
copper traces, and other materials, to the surrounding air.
Low-Noise Operation
An external 0.01μF bypass capacitor at BP, in conjunc-
tion with an internal resistor, creates a lowpass filter.
The MAX8532 exhibits 40μV RMS output voltage noise
with C BP = 0.01μF and C OUT = 2.2μF (see the Output
Noise Spectral Density vs. Frequency graph in the
Typical Operating Characteristics).
Applications Information
Capacitor Selection
and Regulator Stability
Use a 2.2μF capacitor on the MAX8532’s input. Larger
input capacitor values with lower ESR provide better
supply-noise rejection and line-transient response. To
reduce noise and improve load transients, use large
output capacitors up to 10μF. For stable operation over
the full temperature range and with rated maximum
load currents, use a minimum of 2.2μF (or 1μF for
<150mA loading) for OUT.
Note that some ceramic dielectrics exhibit large capac-
itance and ESR variation with temperature. With
dielectrics such as Z5U and Y5V, use 4.7μF or more to
ensure stability at temperatures below -10°C. With X7R
or X5R dielectrics, 2.2μF is sufficient at all operating
temperatures. These regulators are optimized for
ceramic capacitors. Tantalum capacitors are not rec-
ommended.
PSRR and Operation from
Sources Other than Batteries
The MAX8532 is designed to deliver low dropout volt-
ages and low quiescent currents in battery-powered sys-
tems. Power-supply rejection is 62dB at low frequencies
(see the Power-Supply Rejection Ratio vs. Frequency
graph in the Typical Operating Characteristics).
When operating from sources other than batteries,
improve supply-noise rejection and transient response
by increasing the values of the input and output bypass
capacitors and through passive filtering techniques.
6
_______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| ECM15DRSN-S288 | CONN EDGECARD 30POS .156 EXTEND |
| VE-J3T-CX-F2 | CONVERTER MOD DC/DC 6.5V 75W |
| MPG06A-E3/54 | DIODE 1A 50V MINI MPG06 |
| EEM28DRSH-S288 | CONN EDGECARD 56POS .156 EXTEND |
| GBM18DTBD-S189 | CONN EDGECARD 36POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8532EBTG | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX8532EBTG-T | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX8532EBTJ | 制造商:Maxim Integrated Products 功能描述:LOW-NOISE LOW-DROPOUT 200MA LINEA - Rail/Tube 制造商:Rochester Electronics LLC 功能描述: |
| MAX8532EBTJ+T | 功能描述:低压差稳压器 - LDO 200mA Linear Regulator RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX8532EBTJ-T | 功能描述:低压差稳压器 - LDO 200mA Linear Regulator RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。