参数资料
| 型号： | MAX8532EBTJ+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 5/8页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 2.85V .2A 6-UCSP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 2.85V |
| 输入电压： | 最高 6.5V |
| 电压 - 压降（标准）： | 0.1V @ 100mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 200mA（最小） |
| 电流 - 限制（最小）： | 210mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-WFBGA，CSPBGA |
| 供应商设备封装： | 6-uCSP（1.57x1.16） |
| 包装： | 带卷 (TR) |
Low-Noise, Low-Dropout,
200mA Linear Regulator in UCSP
Functional Diagram
IN
SHDN
SHUTDOWN
AND
POWER-ON
CONTROL
THERMAL
SENSOR
1.25V
REF
ERROR
AMP
MAX8532
MOS
DRIVER
WITH I LIMIT
OUT
GND
BP
Detailed Description
The MAX8532 is a low-power, low-dropout, low-quies-
cent current linear regulator designed primarily for bat-
tery-powered applications. For preset output voltages,
see the Output Voltage Selector Guide. The device
supplies up to 200mA for OUT. The MAX8532 consists
of a 1.25V reference, error amplifier, P-channel pass
transistor, reference bypass block, and internal feed-
back voltage divider.
The 1.25V bandgap reference is connected to the error
amplifier’s inverting input. The error amplifier compares
this reference with the feedback voltage and amplifies
the difference. If the feedback voltage is lower than the
reference voltage, the pass-transistor gate is pulled
lower, allowing more current to pass to the output and
increasing the output voltage. If the feedback voltage is
high, the pass-transistor gate is pulled up, allowing less
current to pass to the output. The output voltage is fed
back through an internal resistor voltage-divider con-
nected to the OUT pin.
Shutdown
The MAX8532 has a single shutdown control input
( SHDN ). Drive SHDN low to shut down the output,
reducing supply current to 10nA. Connect SHDN to a
logic-high, or IN, for normal operation.
Internal P-Channel Pass Transistor
The MAX8532 features a 1 ? P-channel MOSFET pass
transistor. A P-channel MOSFET provides several advan-
tages over similar designs using PNP pass transistors,
including longer battery life. It requires no base drive,
reducing quiescent current. PNP-based regulators waste
considerable current in dropout when the pass transistor
saturates and also use high base-drive currents under
heavy loads. The MAX8532 does not suffer these prob-
lems and consumes only 90μA quiecent current whether
in dropout, light-load, or heavy-load applications (see the
Typical Operating Characteristics). Whereas a PNP-
based regulator has dropout voltage independent of the
load, a P-channel MOSFET’s dropout voltage is propor-
tional to load current, providing for low dropout voltage
at heavy loads and extremely low dropout voltage at
lighter loads.
_______________________________________________________________________________________
5
相关PDF资料 |
PDF描述 |
|---|---|
| MAX8536EUA+ | IC CNTRLR ORING MOSFET 8-MSOP |
| MAX8539EEI+ | IC CNTRLR BUCK DUAL 28-QSOP |
| MAX8540EEE+T | IC REG CTRLR PWM CM 16-QSOP |
| MAX8545EUB+T | IC REG CTRLR BUCK PWM VM 10-UMAX |
| MAX8550AETI+T | IC PWR SUP DDR INTEG 28TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8533EUB | 功能描述:热插拔功率分布 RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX8533EUB+ | 功能描述:热插拔功率分布 12V InfiniBand-Comp Hot-Swap Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX8533EUB+T | 功能描述:热插拔功率分布 12V InfiniBand-Comp Hot-Swap Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX8533EUB-T | 功能描述:热插拔功率分布 RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX8533EVKIT | 制造商:Maxim Integrated Products 功能描述:SMALLEST 12V INFINIBAND-COMPLIANT - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。