- 您现在的位置：买卖IC网 > PDF目录22149 > MAX8556ETE/V+ (Maxim Integrated)IC REG LDO ADJ 4A 16WQFN PDF资料下载
参数资料
| 型号： | MAX8556ETE/V+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 7/10页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO ADJ 4A 16WQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 60 |
| 稳压器拓扑结构： | 正，可调式 |
| 输出电压： | 0.5 V ~ 3.4 V |
| 输入电压： | 1.43 V ~ 3.6 V |
| 电压 - 压降（标准）： | 0.1V @ 4A |
| 稳压器数量： | 1 |
| 电流 - 输出： | 4A |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WQFN 裸露焊盘 |
| 供应商设备封装： | 16-TQFN-EP（5x5） |
| 包装： | 管件 |
4A Ultra-Low-Input-Voltage
LDO Regulators
Detailed Description
The MAX8556/MAX8557 low-dropout linear regulators
are capable of delivering up to 4A from low-input volt-
age supplies ranging from 1.425V to 3.6V with only
200mV of dropout (max). The pMOS output stage can
be driven from input voltages down to 1.425V without
sacrificing stability or transient performance. Supply
current is not a significant function of load or input head-
room because this regulator has a pMOS output device.
The MAX8556/MAX8557 are fully protected from an out-
put short circuit by current-limiting and thermal-overload
circuitry. The low-power shutdown mode reduces sup-
ply current to 0.2μA (typ) to maximize battery life in
portable applications. The MAX8556 includes an open-
drain power-OK signal (POK) that goes high when the
regulator output is within ±10% of its nominal output
voltage. The MAX8557 includes an open-drain power-
on-reset output (POR) that goes high 140ms after the
output has risen above 90% of its nominal value.
Internal p-Channel Pass Transistor
The MAX8556/MAX8557 feature a 25m ? p-channel
MOSFET pass transistor. Unlike similar designs using
pnp pass transistors, p-channel MOSFETs require no
base drive, which reduces quiescent current; pnp-
based regulators also waste considerable current in
dropout when the pass transistor saturates, and use
high base-drive currents under large loads. The
MAX8556/MAX8557 do not suffer from these problems
and consume only 800μA (typ) of quiescent current
under heavy loads, as well as in dropout.
Short-Circuit/Thermal Fault Protection
The MAX8556/MAX8557 are fully protected from output
short circuits through current-limiting and thermal-over-
load circuitry. When the output is shorted to ground, the
output current is foldback limited to 3A (max). Under
these conditions, the device quickly heats up. When
the junction temperature reaches +160°C, the thermal-
overload circuitry turns off the output, allowing the
device to cool. When the junction cools to +115°C, the
output turns back on and attempts to establish regula-
tion. Current limiting and thermal protection continue
until the fault is removed.
Shutdown Mode
The MAX8556/MAX8557 feature a low-power shutdown
mode that reduces quiescent current to 0.2μA (typ).
Drive EN low to disable the voltage reference, error
amplifier, gate-drive circuitry, and pass transistor, and
pull the output low with 5k ? impedance. Drive EN high
or connect to IN for normal operation.
Power-OK Output (POK, MAX8556 Only)
The MAX8556 features a power-OK (POK) output to
indicate the status of the output. POK is high impedance
when the regulator output is within ±10% of its nominal
output voltage. If the output voltage falls/rises outside
this range or the IC experiences thermal fault, POK is
internally pulled low. This open-drain output requires an
external pullup resistor to V IN or another logic supply
below 3.6V. For glitch immunity, an internal delay circuit
prevents the output from switching for 50μs (typ) after
the trip threshold is initially reached. POK is low when
the IC is in shutdown mode.
Power-On Reset (POR, MAX8557 Only)
The MAX8557 features a power-on reset output that
goes high impedance 140ms (typ) after the output
reaches 90% of its nominal value. This open-drain out-
put requires an external pullup resistor to V IN or another
logic supply less than 3.6V. When the output falls below
90% of the nominal output voltage or the IC experi-
ences a thermal fault, POR immediately transitions low.
POR is low when the IC is in shutdown mode.
Operating Region and Power Dissipation
The maximum power dissipation depends on the ther-
mal resistance of the IC package and the circuit board,
the temperature difference between the die junction and
ambient air, and the rate of ambient airflow. The power
dissipated by the IC is P = I OUT x (V IN - V OUT ). Proper
PCB layout can increase the allowed power dissipation
by dissipating heat in the board instead of the package.
See the Thermal Considerations in PCB Layout section
for more details.
_______________________________________________________________________________________
7
相关PDF资料 |
PDF描述 |
|---|---|
| EPM7128SLI84-10N | IC MAX 7000 CPLD 128 84-PLCC |
| EPM7128SLI84-10 | IC MAX 7000 CPLD 128 84-PLCC |
| MAX604EPA+ | IC REG LDO 3.3V/ADJ .5A 8-DIP |
| 7-530666-2 | CONN LOW PRO 10 POS 156X200C/L |
| TAJA226K004RNJ | CAP TANT 22UF 4V 10% 1206 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8556EVKIT | 功能描述:低压差稳压器 - LDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX8557ETE | 功能描述:低压差稳压器 - LDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX8557ETE+ | 功能描述:低压差稳压器 - LDO 4A Ultra-Low-Input-V LDO Regulator RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX8557ETE+T | 功能描述:低压差稳压器 - LDO 4A Ultra-Low-Input-V LDO Regulator RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX8557ETE-T | 功能描述:低压差稳压器 - LDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。