- 您现在的位置：买卖IC网 > PDF目录17121 > MAX8568AETE+ (Maxim Integrated Products)IC BATT MANAGE LITH 16-TQFN PDF资料下载
参数资料
| 型号： | MAX8568AETE+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 9/17页 |
| 文件大小： | 0K |
| 描述： | IC BATT MANAGE LITH 16-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 100 |
| 功能： | 备份管理 |
| 电池化学： | 锂离子（Li-Ion）；镍金属氢化物（NiMH） |
| 电源电压： | 2.8 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WFQFN 裸露焊盘 |
| 供应商设备封装： | 16-TQFN-EP（3x3） |
| 包装： | 管件 |
Complete Backup-Management ICs
for Lithium and NiMH Batteries
Detailed Description
The MAX8568A/MAX8568B are compact ICs for manag-
ing backup battery charging and utilization in PDAs and
other smart handheld devices. The MAX8568A/
MAX8568B are comprised of three major blocks: 1) A
multichemistry charger for small lithium-ion, lithium-man-
ganese, LiVeO 5 , and NiMH batteries; 2) a small very-
low-current step-up DC-DC converter that generates a
boosted backup supply when the backup battery output
is less than required; and 3) an LDO that supplies a
second backup voltage to an additional system block
(typically low-voltage RAM).
Multichemistry Charger
The backup battery charger charges most types of
rechargeable lithium and NiMH cells. Charging current
can be set up to 25mA by a resistor connected from
CHGI to GND. The charger operates a current-limited
voltage source for rechargeable lithium batteries, and
switches between fast and trickle charging for NiMH
batteries.
NiMH Charging Scheme
The NiMH charger operates at two different charge cur-
rents based upon the voltages at TERMV and STRTV.
V STRTV sets the BK voltage below which fast charging
(set by CHGI) occurs. V TERMV sets the upper BK trip
point where fast charging stops and trickle charging
begins, and also sets a maximum voltage limit for the
NiMH battery. If V TERMV is 1.2V, then fast charge stops
at 1.2 / 0.86 = 1.4V, and the maximum voltage limit is
1.2 / 0.67 = 1.791V.
An NiMH battery fast charges until it hits 1.4V set by
V TERMV . The charger then switches to trickle charge at
a current that is 10% of fast charge (set by CHGI). If the
voltage drops (due to loading or self-discharge) to 1.2V
(with V STRTV = 1.2V), fast charge resumes. If the volt-
age then increases back to 1.4V (with V TERMV = 1.2V),
trickle charge resumes. If the cell voltage reaches 1.8V,
the charge current falls to zero.
Lithium Charging Scheme
When charging rechargeable lithium-type batteries,
V TERMV sets the charging voltage while V STRTV is unused.
Charge current is set by a resistor from CHGI to GND.
There is no trickle charge for lithium mode. This charging
scheme is essentially a current-limited voltage source.
Step-Up DC-DC Converter
If an NiMH battery or lower-voltage rechargeable lithium
battery is used for backup, it may be necessary to boost
the battery voltage to 2.5V, 3.3V, or some other voltage to
power RAM, RTC, or other devices. The step-up DC-DC
converter is powered by the backup battery but requires
that the I/O supply be activated at least one time before
the backup battery can be stepped up. This allows the
end product to draw no backup battery current while “on
the shelf” waiting for its first activation. The step-up DC-
DC converter is enabled, and reaches regulation, 50μs
(typ) after INOK falls below 2.43V (typ).
The step-up converter includes a built-in synchronous
rectifier that reduces cost by eliminating the need for
an external diode and improves overall efficiency. The
converter also features a clamp circuit that reduces
EMI due to inductor ringing. The output voltage is set to
3.3V or 2.5V by connecting BKV to either GND or
BKSU, respectively. For adjustable output, connect
BKV to a resistor-divider from BKSU to GND.
LDO
For designs that require two different backup voltages,
the MAX8568 includes a small LDO that is powered from
BKSU. This LDO can supply up to 10mA and uses only
5μA of operating current. The LDO output is preset to
2.5V in the MAX8568A and 1.8V in the MAX8568B. The
LDO is activated after V INOK falls below 2.43V (typ).
Switchover Behavior
See Figure 1 for switchover timing. If the backup bat-
tery is connected to the system before main power, the
MAX8568 remains off and draws very little current, typi-
cally less than 0.5μA. This allows the end product to
draw no backup battery current while “on the shelf”
waiting for its first activation. When main power is con-
nected, the MAX8568 powers on, assuming the main
battery is greater than 2.8V. The MAX8568 begins to
charge the backup battery if needed (see the
Multichemistry Charger section). The OD1 and OD2
outputs pull to GND and turn on the external p-channel
MOSFETs. This allows the voltage on I/O IN and MEM
IN (Figure 7) to pass through to the I/O OUT and MEM
OUT outputs. These I/O and MEM voltages are typically
provided by a MAX1586/MAX1587 power-supply IC.
INOK monitors the main battery voltage and activates
the backup boost converter and LDO when the voltage
on V INOK falls below 2.43V. The backup converter
starts 50μs after V INOK falls. OD1 and OD2 go high
impedance and turn off the external p-channel
MOSFETs. These MOSFETs disconnect the I/O IN and
MEM IN inputs from the load. This ensures that the I/O
and MEM main supplies do not draw current from the
backup source (MAX8568). The charger also turns off
when INOK is less than 2.43V.
If the MAX8568 is being evaluated as a stand-alone
device, note that the backup-battery boost converter will
not operate unless I/O IN has been activated at least one
time. The typical power removal sequence for testing is 1)
main battery goes low, then 2) MEM IN and I/O IN go low.
_______________________________________________________________________________________
9
相关PDF资料 |
PDF描述 |
|---|---|
| SEK331M050ST | CAP ALUM 330UF 50V 20% RADIAL |
| ADR06ARZ-REEL7 | IC VREF SERIES PREC 3V 8-SOIC |
| VI-JTW-EZ | CONVERTER MOD DC/DC 5.5V 25W |
| GEM15DTAT | CONN EDGECARD 30POS R/A .156 SLD |
| UVZ1E332MHD | CAP ALUM 3300UF 25V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8568AETE+ | 功能描述:电池管理 Backup-Mgt IC for Li & NiMH Bat RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX8568AETE+T | 功能描述:电池管理 Backup-Mgt IC for Li & NiMH Bat RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX8568AETE-T | 功能描述:电池管理 Backup-Mgt IC for Li & NiMH Bat RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX8568BETE | 功能描述:电池管理 Backup-Mgt IC for Li & NiMH Bat RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX8568BETE-T | 功能描述:电池管理 Backup-Mgt IC for Li & NiMH Bat RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。