- 您现在的位置：买卖IC网 > PDF目录13567 > MAX859CSA+ (Maxim Integrated Products)IC REG BOOST ADJ 60MA 8SOIC PDF资料下载
参数资料
| 型号： | MAX859CSA+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 6/12页 |
| 文件大小： | 0K |
| 描述： | IC REG BOOST ADJ 60MA 8SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 100 |
| 类型： | 升压（升压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 2.7 V ~ 6 V |
| 输入电压： | 0.8 V ~ 6 V |
| 频率 - 开关： | 500kHz |
| 电流 - 输出： | 60mA |
| 同步整流器： | 无 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 管件 |
| 供应商设备封装： | 8-SOIC |
3.3V/5V or Adjustable-Output,
Step-Up DC-DC Converters
______________________________________________________________Pin Description
PIN
MAX856
MAX858
1
2
—
3
4
5
6
7
8
MAX857
MAX859
1
—
2
3
4
5
6
7
8
NAME
– — — — –
S H D N
– –
3/ 5
FB
REF
LBO
LBI
OUT
GND
LX
FUNCTION
Shutdown Input. When low, the entire circuit is off and V OUT = V IN - V D, where V D is the
forward voltage drop of the external Schottky rectifier.
Selects the output voltage; connect to GND for 5V output, and to OUT for 3.3V
output.
Feedback Input for adjustable-output operation. Connect to an external resistor voltage
divider between OUT and GND.
1.25V Reference Voltage Output. Bypass with 0.22μF to GND (0.1μF if there is no external
reference load). Maximum load capability is 250μA source, 20μA sink.
Low-Battery Output. An open-drain N-channel MOSFET sinks current when the voltage at
LBI drops below 1.25V.
Low-Battery Input. When the voltage on LBI drops below 1.25V, LBO sinks current.
If not used, connect to V IN .
Connect OUT to the regulator output. OUT provides bootstrap power to the IC.
Power Ground. Must be low impedance; solder directly to ground plane.
N-Channel Power-MOSFET Drain
_______________Detailed Description
Operating Principle
The MAX856–MAX859 combine a switch-mode regula-
tor, N-channel power MOSFET, precision voltage refer-
ence, and power-fail detector in a single monolithic
device. The MOSFET is a “sense-FET” type for best
efficiency, and has a very low gate threshold voltage to
ensure start-up with low battery voltages (0.8V typ).
PFM Control Scheme
A unique minimum-off-time, current-limited pulse-fre-
quency modulation (PFM) control scheme is a key fea-
ture of the MAX856 series (Figure 1). This scheme
combines the high output power and efficiency of a
pulse-width modulation (PWM) device with the ultra-low
quiescent current of a traditional PFM pulse-skipper.
There is no oscillator; at heavy loads, switching is
accomplished through a constant-peak-current limit in
the switch, which allows the inductor current to vary
between this peak limit and some lesser value. At light
loads, switching frequency is governed by a pair of
one-shots, which set a minimum off-time (1μs) and a
maximum on-time (4μs). The switching frequency
depends upon the load and the input voltage, and can
range up to 500kHz.
The peak switch current of the internal MOSFET power
switch is fixed at 500mA ±100mA (MAX856/MAX857)
or 125mA ±25mA (MAX858/MAX859). The switch’s on-
resistance is typically 1 ? (MAX856/MAX857) or 4 ?
(MAX858/MAX859), resulting in a switch voltage drop
(V SW ) of about 500mV under high output loads. The
value of V SW will decrease with light current loads.
Conventional PWM converters generate constant-fre-
quency switching noise, whereas the unique architec-
ture of the MAX856–MAX859 produces variable-fre-
quency switching noise. However, unlike conventional
pulse-skippers (where noise amplitude varies with input
voltage), noise in the MAX856 series does not exceed
the switch current limit times the filter-capacitor equiva-
lent series resistance (ESR).
Voltage Reference
The precision voltage reference is suitable for driving
external loads, such as an analog-to-digital converter.
The voltage-reference output changes less than ±2%
when sourcing up to 250μA and sinking up to 20μA. If
the reference drives an external load, bypass it with
0.22μF to GND. If the reference is unloaded, bypass it
with at least 0.1μF.
6
_______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| USP1V3R3MDD | CAP ALUM 3.3UF 35V 20% RADIAL |
| USP1HR22MDD | CAP ALUM 0.22UF 50V 20% RADIAL |
| ECM40DCMD-S288 | CONN EDGECARD 80POS .156 EXTEND |
| MAX619CSA+T | IC REG SWITCHED CAP 5V 8SOIC |
| VI-JNR-EX-F1 | CONVERTER MOD DC/DC 7.5V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX859CSA+ | 功能描述:直流/直流开关转换器 3.3/5/AdjV Step-Up DC/DC Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX859CSA+T | 功能描述:直流/直流开关转换器 3.3/5/AdjV Step-Up DC/DC Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX859CSA-T | 功能描述:直流/直流开关转换器 3.3/5/AdjV Step-Up DC/DC Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX859CSA-W | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX859CUA | 功能描述:直流/直流开关转换器 3.3/5/AdjV Step-Up DC/DC Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。